F030C8xx_KBus.git

QuakeGod

2021-06-20 bfc108e6097eff2bec73050e261f3b9e5db447b7

提交 \| 用户 \| age
bfc108	1	/**
Q	2	******************************************************************************
	3	* @file stm32f0xx_hal_i2c.c
	4	* @author MCD Application Team
	5	* @brief I2C HAL module driver.
	6	* This file provides firmware functions to manage the following
	7	* functionalities of the Inter Integrated Circuit (I2C) peripheral:
	8	* + Initialization and de-initialization functions
	9	* + IO operation functions
	10	* + Peripheral State and Errors functions
	11	*
	12	@verbatim
	13	==============================================================================
	14	##### How to use this driver #####
	15	==============================================================================
	16	[..]
	17	The I2C HAL driver can be used as follows:
	18
	19	(#) Declare a I2C_HandleTypeDef handle structure, for example:
	20	I2C_HandleTypeDef hi2c;
	21
	22	(#)Initialize the I2C low level resources by implementing the HAL_I2C_MspInit() API:
	23	(##) Enable the I2Cx interface clock
	24	(##) I2C pins configuration
	25	(+++) Enable the clock for the I2C GPIOs
	26	(+++) Configure I2C pins as alternate function open-drain
	27	(##) NVIC configuration if you need to use interrupt process
	28	(+++) Configure the I2Cx interrupt priority
	29	(+++) Enable the NVIC I2C IRQ Channel
	30	(##) DMA Configuration if you need to use DMA process
	31	(+++) Declare a DMA_HandleTypeDef handle structure for the transmit or receive channel
	32	(+++) Enable the DMAx interface clock using
	33	(+++) Configure the DMA handle parameters
	34	(+++) Configure the DMA Tx or Rx channel
	35	(+++) Associate the initialized DMA handle to the hi2c DMA Tx or Rx handle
	36	(+++) Configure the priority and enable the NVIC for the transfer complete interrupt on
	37	the DMA Tx or Rx channel
	38
	39	(#) Configure the Communication Clock Timing, Own Address1, Master Addressing mode, Dual Addressing mode,
	40	Own Address2, Own Address2 Mask, General call and Nostretch mode in the hi2c Init structure.
	41
	42	(#) Initialize the I2C registers by calling the HAL_I2C_Init(), configures also the low level Hardware
	43	(GPIO, CLOCK, NVIC...etc) by calling the customized HAL_I2C_MspInit(&hi2c) API.
	44
	45	(#) To check if target device is ready for communication, use the function HAL_I2C_IsDeviceReady()
	46
	47	(#) For I2C IO and IO MEM operations, three operation modes are available within this driver :
	48
	49	* Polling mode IO operation *
	50	=================================
	51	[..]
	52	(+) Transmit in master mode an amount of data in blocking mode using HAL_I2C_Master_Transmit()
	53	(+) Receive in master mode an amount of data in blocking mode using HAL_I2C_Master_Receive()
	54	(+) Transmit in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Transmit()
	55	(+) Receive in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Receive()
	56
	57	* Polling mode IO MEM operation *
	58	=====================================
	59	[..]
	60	(+) Write an amount of data in blocking mode to a specific memory address using HAL_I2C_Mem_Write()
	61	(+) Read an amount of data in blocking mode from a specific memory address using HAL_I2C_Mem_Read()
	62
	63
	64	* Interrupt mode IO operation *
	65	===================================
	66	[..]
	67	(+) Transmit in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Transmit_IT()
	68	(+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can
	69	add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
	70	(+) Receive in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Receive_IT()
	71	(+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can
	72	add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
	73	(+) Transmit in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Transmit_IT()
	74	(+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can
	75	add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
	76	(+) Receive in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Receive_IT()
	77	(+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can
	78	add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
	79	(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can
	80	add his own code by customization of function pointer HAL_I2C_ErrorCallback()
	81	(+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
	82	(+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can
	83	add his own code by customization of function pointer HAL_I2C_AbortCpltCallback()
	84	(+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
	85	This action will inform Master to generate a Stop condition to discard the communication.
	86
	87
	88	* Interrupt mode IO sequential operation *
	89	==============================================
	90	[..]
	91	(@) These interfaces allow to manage a sequential transfer with a repeated start condition
	92	when a direction change during transfer
	93	[..]
	94	(+) A specific option field manage the different steps of a sequential transfer
	95	(+) Option field values are defined through @ref I2C_XFEROPTIONS and are listed below:
	96	(++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functionnal is same as associated interfaces in no sequential mode
	97	(++) I2C_FIRST_FRAME: Sequential usage, this option allow to manage a sequence with start condition, address
	98	and data to transfer without a final stop condition
	99	(++) I2C_FIRST_AND_NEXT_FRAME: Sequential usage (Master only), this option allow to manage a sequence with start condition, address
	100	and data to transfer without a final stop condition, an then permit a call the same master sequential interface
	101	several times (like HAL_I2C_Master_Sequential_Transmit_IT() then HAL_I2C_Master_Sequential_Transmit_IT())
	102	(++) I2C_NEXT_FRAME: Sequential usage, this option allow to manage a sequence with a restart condition, address
	103	and with new data to transfer if the direction change or manage only the new data to transfer
	104	if no direction change and without a final stop condition in both cases
	105	(++) I2C_LAST_FRAME: Sequential usage, this option allow to manage a sequance with a restart condition, address
	106	and with new data to transfer if the direction change or manage only the new data to transfer
	107	if no direction change and with a final stop condition in both cases
	108
	109	(+) Differents sequential I2C interfaces are listed below:
	110	(++) Sequential transmit in master I2C mode an amount of data in non-blocking mode using HAL_I2C_Master_Sequential_Transmit_IT()
	111	(+++) At transmission end of current frame transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can
	112	add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
	113	(++) Sequential receive in master I2C mode an amount of data in non-blocking mode using HAL_I2C_Master_Sequential_Receive_IT()
	114	(+++) At reception end of current frame transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can
	115	add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
	116	(++) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
	117	(+++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can
	118	add his own code by customization of function pointer HAL_I2C_AbortCpltCallback()
	119	(++) Enable/disable the Address listen mode in slave I2C mode using HAL_I2C_EnableListen_IT() HAL_I2C_DisableListen_IT()
	120	(+++) When address slave I2C match, HAL_I2C_AddrCallback() is executed and user can
	121	add his own code to check the Address Match Code and the transmission direction request by master (Write/Read).
	122	(+++) At Listen mode end HAL_I2C_ListenCpltCallback() is executed and user can
	123	add his own code by customization of function pointer HAL_I2C_ListenCpltCallback()
	124	(++) Sequential transmit in slave I2C mode an amount of data in non-blocking mode using HAL_I2C_Slave_Sequential_Transmit_IT()
	125	(+++) At transmission end of current frame transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can
	126	add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
	127	(++) Sequential receive in slave I2C mode an amount of data in non-blocking mode using HAL_I2C_Slave_Sequential_Receive_IT()
	128	(+++) At reception end of current frame transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can
	129	add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
	130	(++) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can
	131	add his own code by customization of function pointer HAL_I2C_ErrorCallback()
	132	(++) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
	133	(++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can
	134	add his own code by customization of function pointer HAL_I2C_AbortCpltCallback()
	135	(++) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
	136	This action will inform Master to generate a Stop condition to discard the communication.
	137
	138	* Interrupt mode IO MEM operation *
	139	=======================================
	140	[..]
	141	(+) Write an amount of data in non-blocking mode with Interrupt to a specific memory address using
	142	HAL_I2C_Mem_Write_IT()
	143	(+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and user can
	144	add his own code by customization of function pointer HAL_I2C_MemTxCpltCallback()
	145	(+) Read an amount of data in non-blocking mode with Interrupt from a specific memory address using
	146	HAL_I2C_Mem_Read_IT()
	147	(+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and user can
	148	add his own code by customization of function pointer HAL_I2C_MemRxCpltCallback()
	149	(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can
	150	add his own code by customization of function pointer HAL_I2C_ErrorCallback()
	151
	152	* DMA mode IO operation *
	153	==============================
	154	[..]
	155	(+) Transmit in master mode an amount of data in non-blocking mode (DMA) using
	156	HAL_I2C_Master_Transmit_DMA()
	157	(+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and user can
	158	add his own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
	159	(+) Receive in master mode an amount of data in non-blocking mode (DMA) using
	160	HAL_I2C_Master_Receive_DMA()
	161	(+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and user can
	162	add his own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
	163	(+) Transmit in slave mode an amount of data in non-blocking mode (DMA) using
	164	HAL_I2C_Slave_Transmit_DMA()
	165	(+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and user can
	166	add his own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
	167	(+) Receive in slave mode an amount of data in non-blocking mode (DMA) using
	168	HAL_I2C_Slave_Receive_DMA()
	169	(+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and user can
	170	add his own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
	171	(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can
	172	add his own code by customization of function pointer HAL_I2C_ErrorCallback()
	173	(+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
	174	(+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and user can
	175	add his own code by customization of function pointer HAL_I2C_AbortCpltCallback()
	176	(+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
	177	This action will inform Master to generate a Stop condition to discard the communication.
	178
	179	* DMA mode IO MEM operation *
	180	=================================
	181	[..]
	182	(+) Write an amount of data in non-blocking mode with DMA to a specific memory address using
	183	HAL_I2C_Mem_Write_DMA()
	184	(+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and user can
	185	add his own code by customization of function pointer HAL_I2C_MemTxCpltCallback()
	186	(+) Read an amount of data in non-blocking mode with DMA from a specific memory address using
	187	HAL_I2C_Mem_Read_DMA()
	188	(+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and user can
	189	add his own code by customization of function pointer HAL_I2C_MemRxCpltCallback()
	190	(+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and user can
	191	add his own code by customization of function pointer HAL_I2C_ErrorCallback()
	192
	193
	194	* I2C HAL driver macros list *
	195	==================================
	196	[..]
	197	Below the list of most used macros in I2C HAL driver.
	198
	199	(+) __HAL_I2C_ENABLE: Enable the I2C peripheral
	200	(+) __HAL_I2C_DISABLE: Disable the I2C peripheral
	201	(+) __HAL_I2C_GENERATE_NACK: Generate a Non-Acknowledge I2C peripheral in Slave mode
	202	(+) __HAL_I2C_GET_FLAG: Check whether the specified I2C flag is set or not
	203	(+) __HAL_I2C_CLEAR_FLAG: Clear the specified I2C pending flag
	204	(+) __HAL_I2C_ENABLE_IT: Enable the specified I2C interrupt
	205	(+) __HAL_I2C_DISABLE_IT: Disable the specified I2C interrupt
	206
	207	[..]
	208	(@) You can refer to the I2C HAL driver header file for more useful macros
	209
	210	@endverbatim
	211	******************************************************************************
	212	* @attention
	213	*
	214	* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
	215	*
	216	* Redistribution and use in source and binary forms, with or without modification,
	217	* are permitted provided that the following conditions are met:
	218	* 1. Redistributions of source code must retain the above copyright notice,
	219	* this list of conditions and the following disclaimer.
	220	* 2. Redistributions in binary form must reproduce the above copyright notice,
	221	* this list of conditions and the following disclaimer in the documentation
	222	* and/or other materials provided with the distribution.
	223	* 3. Neither the name of STMicroelectronics nor the names of its contributors
	224	* may be used to endorse or promote products derived from this software
	225	* without specific prior written permission.
	226	*
	227	* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
	228	* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
	229	* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
	230	* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
	231	* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
	232	* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
	233	* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
	234	* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
	235	* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
	236	* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
	237	*
	238	******************************************************************************
	239	*/
	240
	241	/* Includes ------------------------------------------------------------------*/
	242	#include "stm32f0xx_hal.h"
	243
	244	/** @addtogroup STM32F0xx_HAL_Driver
	245	* @{
	246	*/
	247
	248	/** @defgroup I2C I2C
	249	* @brief I2C HAL module driver
	250	* @{
	251	*/
	252
	253	#ifdef HAL_I2C_MODULE_ENABLED
	254
	255	/* Private typedef -----------------------------------------------------------*/
	256	/* Private define ------------------------------------------------------------*/
	257
	258	/** @defgroup I2C_Private_Define I2C Private Define
	259	* @{
	260	*/
	261	#define TIMING_CLEAR_MASK (0xF0FFFFFFU) /!< I2C TIMING clear register Mask /
	262	#define I2C_TIMEOUT_ADDR (10000U) /!< 10 s /
	263	#define I2C_TIMEOUT_BUSY (25U) /!< 25 ms /
	264	#define I2C_TIMEOUT_DIR (25U) /!< 25 ms /
	265	#define I2C_TIMEOUT_RXNE (25U) /!< 25 ms /
	266	#define I2C_TIMEOUT_STOPF (25U) /!< 25 ms /
	267	#define I2C_TIMEOUT_TC (25U) /!< 25 ms /
	268	#define I2C_TIMEOUT_TCR (25U) /!< 25 ms /
	269	#define I2C_TIMEOUT_TXIS (25U) /!< 25 ms /
	270	#define I2C_TIMEOUT_FLAG (25U) /!< 25 ms /
	271
	272	#define MAX_NBYTE_SIZE 255U
	273	#define SlaveAddr_SHIFT 7U
	274	#define SlaveAddr_MSK 0x06U
	275
	276	/* Private define for @ref PreviousState usage */
	277	#define I2C_STATE_MSK ((uint32_t)((HAL_I2C_STATE_BUSY_TX \| HAL_I2C_STATE_BUSY_RX) & (~((uint32_t)HAL_I2C_STATE_READY)))) /!< Mask State define, keep only RX and TX bits /
	278	#define I2C_STATE_NONE ((uint32_t)(HAL_I2C_MODE_NONE)) /!< Default Value /
	279	#define I2C_STATE_MASTER_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) \| HAL_I2C_MODE_MASTER)) /!< Master Busy TX, combinaison of State LSB and Mode enum /
	280	#define I2C_STATE_MASTER_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) \| HAL_I2C_MODE_MASTER)) /!< Master Busy RX, combinaison of State LSB and Mode enum /
	281	#define I2C_STATE_SLAVE_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) \| HAL_I2C_MODE_SLAVE)) /!< Slave Busy TX, combinaison of State LSB and Mode enum /
	282	#define I2C_STATE_SLAVE_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) \| HAL_I2C_MODE_SLAVE)) /!< Slave Busy RX, combinaison of State LSB and Mode enum /
	283	#define I2C_STATE_MEM_BUSY_TX ((uint32_t)((HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) \| HAL_I2C_MODE_MEM)) /!< Memory Busy TX, combinaison of State LSB and Mode enum /
	284	#define I2C_STATE_MEM_BUSY_RX ((uint32_t)((HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) \| HAL_I2C_MODE_MEM)) /!< Memory Busy RX, combinaison of State LSB and Mode enum /
	285
	286
	287	/* Private define to centralize the enable/disable of Interrupts */
	288	#define I2C_XFER_TX_IT (0x00000001U)
	289	#define I2C_XFER_RX_IT (0x00000002U)
	290	#define I2C_XFER_LISTEN_IT (0x00000004U)
	291
	292	#define I2C_XFER_ERROR_IT (0x00000011U)
	293	#define I2C_XFER_CPLT_IT (0x00000012U)
	294	#define I2C_XFER_RELOAD_IT (0x00000012U)
	295
	296	/* Private define Sequential Transfer Options default/reset value */
	297	#define I2C_NO_OPTION_FRAME (0xFFFF0000U)
	298	/**
	299	* @}
	300	*/
	301
	302	/* Private macro -------------------------------------------------------------*/
	303	#define I2C_GET_DMA_REMAIN_DATA(__HANDLE__) ((((__HANDLE__)->State) == HAL_I2C_STATE_BUSY_TX) ? \
	304	((uint32_t)((__HANDLE__)->hdmatx->Instance->CNDTR)) : \
	305	((uint32_t)((__HANDLE__)->hdmarx->Instance->CNDTR)))
	306
	307	/* Private variables ---------------------------------------------------------*/
	308	/* Private function prototypes -----------------------------------------------*/
	309
	310	/** @defgroup I2C_Private_Functions I2C Private Functions
	311	* @{
	312	*/
	313	/* Private functions to handle DMA transfer */
	314	static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma);
	315	static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma);
	316	static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma);
	317	static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma);
	318	static void I2C_DMAError(DMA_HandleTypeDef *hdma);
	319	static void I2C_DMAAbort(DMA_HandleTypeDef *hdma);
	320
	321	/* Private functions to handle IT transfer */
	322	static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags);
	323	static void I2C_ITMasterSequentialCplt(I2C_HandleTypeDef *hi2c);
	324	static void I2C_ITSlaveSequentialCplt(I2C_HandleTypeDef *hi2c);
	325	static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags);
	326	static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags);
	327	static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags);
	328	static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode);
	329
	330	/* Private functions to handle IT transfer */
	331	static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart);
	332	static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart);
	333
	334	/* Private functions for I2C transfer IRQ handler */
	335	static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
	336	static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
	337	static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
	338	static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
	339
	340	/* Private functions to handle flags during polling transfer */
	341	static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, uint32_t Timeout, uint32_t Tickstart);
	342	static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
	343	static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
	344	static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
	345	static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
	346
	347	/* Private functions to centralize the enable/disable of Interrupts */
	348	static HAL_StatusTypeDef I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest);
	349	static HAL_StatusTypeDef I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest);
	350
	351	/* Private functions to flush TXDR register */
	352	static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c);
	353
	354	/* Private functions to handle start, restart or stop a transfer */
	355	static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request);
	356	/**
	357	* @}
	358	*/
	359
	360	/* Exported functions --------------------------------------------------------*/
	361
	362	/** @defgroup I2C_Exported_Functions I2C Exported Functions
	363	* @{
	364	*/
	365
	366	/** @defgroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions
	367	* @brief Initialization and Configuration functions
	368	*
	369	@verbatim
	370	===============================================================================
	371	##### Initialization and de-initialization functions #####
	372	===============================================================================
	373	[..] This subsection provides a set of functions allowing to initialize and
	374	deinitialize the I2Cx peripheral:
	375
	376	(+) User must Implement HAL_I2C_MspInit() function in which he configures
	377	all related peripherals resources (CLOCK, GPIO, DMA, IT and NVIC ).
	378
	379	(+) Call the function HAL_I2C_Init() to configure the selected device with
	380	the selected configuration:
	381	(++) Clock Timing
	382	(++) Own Address 1
	383	(++) Addressing mode (Master, Slave)
	384	(++) Dual Addressing mode
	385	(++) Own Address 2
	386	(++) Own Address 2 Mask
	387	(++) General call mode
	388	(++) Nostretch mode
	389
	390	(+) Call the function HAL_I2C_DeInit() to restore the default configuration
	391	of the selected I2Cx peripheral.
	392
	393	@endverbatim
	394	* @{
	395	*/
	396
	397	/**
	398	* @brief Initializes the I2C according to the specified parameters
	399	* in the I2C_InitTypeDef and initialize the associated handle.
	400	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	401	* the configuration information for the specified I2C.
	402	* @retval HAL status
	403	*/
	404	HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c)
	405	{
	406	/* Check the I2C handle allocation */
	407	if (hi2c == NULL)
	408	{
	409	return HAL_ERROR;
	410	}
	411
	412	/* Check the parameters */
	413	assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
	414	assert_param(IS_I2C_OWN_ADDRESS1(hi2c->Init.OwnAddress1));
	415	assert_param(IS_I2C_ADDRESSING_MODE(hi2c->Init.AddressingMode));
	416	assert_param(IS_I2C_DUAL_ADDRESS(hi2c->Init.DualAddressMode));
	417	assert_param(IS_I2C_OWN_ADDRESS2(hi2c->Init.OwnAddress2));
	418	assert_param(IS_I2C_OWN_ADDRESS2_MASK(hi2c->Init.OwnAddress2Masks));
	419	assert_param(IS_I2C_GENERAL_CALL(hi2c->Init.GeneralCallMode));
	420	assert_param(IS_I2C_NO_STRETCH(hi2c->Init.NoStretchMode));
	421
	422	if (hi2c->State == HAL_I2C_STATE_RESET)
	423	{
	424	/* Allocate lock resource and initialize it */
	425	hi2c->Lock = HAL_UNLOCKED;
	426
	427	/* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */
	428	HAL_I2C_MspInit(hi2c);
	429	}
	430
	431	hi2c->State = HAL_I2C_STATE_BUSY;
	432
	433	/* Disable the selected I2C peripheral */
	434	__HAL_I2C_DISABLE(hi2c);
	435
	436	/---------------------------- I2Cx TIMINGR Configuration ------------------/
	437	/* Configure I2Cx: Frequency range */
	438	hi2c->Instance->TIMINGR = hi2c->Init.Timing & TIMING_CLEAR_MASK;
	439
	440	/---------------------------- I2Cx OAR1 Configuration ---------------------/
	441	/* Disable Own Address1 before set the Own Address1 configuration */
	442	hi2c->Instance->OAR1 &= ~I2C_OAR1_OA1EN;
	443
	444	/* Configure I2Cx: Own Address1 and ack own address1 mode */
	445	if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_7BIT)
	446	{
	447	hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN \| hi2c->Init.OwnAddress1);
	448	}
	449	else /* I2C_ADDRESSINGMODE_10BIT */
	450	{
	451	hi2c->Instance->OAR1 = (I2C_OAR1_OA1EN \| I2C_OAR1_OA1MODE \| hi2c->Init.OwnAddress1);
	452	}
	453
	454	/---------------------------- I2Cx CR2 Configuration ----------------------/
	455	/* Configure I2Cx: Addressing Master mode */
	456	if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT)
	457	{
	458	hi2c->Instance->CR2 = (I2C_CR2_ADD10);
	459	}
	460	/* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process */
	461	hi2c->Instance->CR2 \|= (I2C_CR2_AUTOEND \| I2C_CR2_NACK);
	462
	463	/---------------------------- I2Cx OAR2 Configuration ---------------------/
	464	/* Disable Own Address2 before set the Own Address2 configuration */
	465	hi2c->Instance->OAR2 &= ~I2C_DUALADDRESS_ENABLE;
	466
	467	/* Configure I2Cx: Dual mode and Own Address2 */
	468	hi2c->Instance->OAR2 = (hi2c->Init.DualAddressMode \| hi2c->Init.OwnAddress2 \| (hi2c->Init.OwnAddress2Masks << 8));
	469
	470	/---------------------------- I2Cx CR1 Configuration ----------------------/
	471	/* Configure I2Cx: Generalcall and NoStretch mode */
	472	hi2c->Instance->CR1 = (hi2c->Init.GeneralCallMode \| hi2c->Init.NoStretchMode);
	473
	474	/* Enable the selected I2C peripheral */
	475	__HAL_I2C_ENABLE(hi2c);
	476
	477	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	478	hi2c->State = HAL_I2C_STATE_READY;
	479	hi2c->PreviousState = I2C_STATE_NONE;
	480	hi2c->Mode = HAL_I2C_MODE_NONE;
	481
	482	return HAL_OK;
	483	}
	484
	485	/**
	486	* @brief DeInitialize the I2C peripheral.
	487	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	488	* the configuration information for the specified I2C.
	489	* @retval HAL status
	490	*/
	491	HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c)
	492	{
	493	/* Check the I2C handle allocation */
	494	if (hi2c == NULL)
	495	{
	496	return HAL_ERROR;
	497	}
	498
	499	/* Check the parameters */
	500	assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
	501
	502	hi2c->State = HAL_I2C_STATE_BUSY;
	503
	504	/* Disable the I2C Peripheral Clock */
	505	__HAL_I2C_DISABLE(hi2c);
	506
	507	/* DeInit the low level hardware: GPIO, CLOCK, NVIC */
	508	HAL_I2C_MspDeInit(hi2c);
	509
	510	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	511	hi2c->State = HAL_I2C_STATE_RESET;
	512	hi2c->PreviousState = I2C_STATE_NONE;
	513	hi2c->Mode = HAL_I2C_MODE_NONE;
	514
	515	/* Release Lock */
	516	__HAL_UNLOCK(hi2c);
	517
	518	return HAL_OK;
	519	}
	520
	521	/**
	522	* @brief Initialize the I2C MSP.
	523	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	524	* the configuration information for the specified I2C.
	525	* @retval None
	526	*/
	527	__weak void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c)
	528	{
	529	/* Prevent unused argument(s) compilation warning */
	530	UNUSED(hi2c);
	531
	532	/* NOTE : This function should not be modified, when the callback is needed,
	533	the HAL_I2C_MspInit could be implemented in the user file
	534	*/
	535	}
	536
	537	/**
	538	* @brief DeInitialize the I2C MSP.
	539	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	540	* the configuration information for the specified I2C.
	541	* @retval None
	542	*/
	543	__weak void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c)
	544	{
	545	/* Prevent unused argument(s) compilation warning */
	546	UNUSED(hi2c);
	547
	548	/* NOTE : This function should not be modified, when the callback is needed,
	549	the HAL_I2C_MspDeInit could be implemented in the user file
	550	*/
	551	}
	552
	553	/**
	554	* @}
	555	*/
	556
	557	/** @defgroup I2C_Exported_Functions_Group2 Input and Output operation functions
	558	* @brief Data transfers functions
	559	*
	560	@verbatim
	561	===============================================================================
	562	##### IO operation functions #####
	563	===============================================================================
	564	[..]
	565	This subsection provides a set of functions allowing to manage the I2C data
	566	transfers.
	567
	568	(#) There are two modes of transfer:
	569	(++) Blocking mode : The communication is performed in the polling mode.
	570	The status of all data processing is returned by the same function
	571	after finishing transfer.
	572	(++) No-Blocking mode : The communication is performed using Interrupts
	573	or DMA. These functions return the status of the transfer startup.
	574	The end of the data processing will be indicated through the
	575	dedicated I2C IRQ when using Interrupt mode or the DMA IRQ when
	576	using DMA mode.
	577
	578	(#) Blocking mode functions are :
	579	(++) HAL_I2C_Master_Transmit()
	580	(++) HAL_I2C_Master_Receive()
	581	(++) HAL_I2C_Slave_Transmit()
	582	(++) HAL_I2C_Slave_Receive()
	583	(++) HAL_I2C_Mem_Write()
	584	(++) HAL_I2C_Mem_Read()
	585	(++) HAL_I2C_IsDeviceReady()
	586
	587	(#) No-Blocking mode functions with Interrupt are :
	588	(++) HAL_I2C_Master_Transmit_IT()
	589	(++) HAL_I2C_Master_Receive_IT()
	590	(++) HAL_I2C_Slave_Transmit_IT()
	591	(++) HAL_I2C_Slave_Receive_IT()
	592	(++) HAL_I2C_Mem_Write_IT()
	593	(++) HAL_I2C_Mem_Read_IT()
	594
	595	(#) No-Blocking mode functions with DMA are :
	596	(++) HAL_I2C_Master_Transmit_DMA()
	597	(++) HAL_I2C_Master_Receive_DMA()
	598	(++) HAL_I2C_Slave_Transmit_DMA()
	599	(++) HAL_I2C_Slave_Receive_DMA()
	600	(++) HAL_I2C_Mem_Write_DMA()
	601	(++) HAL_I2C_Mem_Read_DMA()
	602
	603	(#) A set of Transfer Complete Callbacks are provided in non Blocking mode:
	604	(++) HAL_I2C_MemTxCpltCallback()
	605	(++) HAL_I2C_MemRxCpltCallback()
	606	(++) HAL_I2C_MasterTxCpltCallback()
	607	(++) HAL_I2C_MasterRxCpltCallback()
	608	(++) HAL_I2C_SlaveTxCpltCallback()
	609	(++) HAL_I2C_SlaveRxCpltCallback()
	610	(++) HAL_I2C_ErrorCallback()
	611
	612	@endverbatim
	613	* @{
	614	*/
	615
	616	/**
	617	* @brief Transmits in master mode an amount of data in blocking mode.
	618	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	619	* the configuration information for the specified I2C.
	620	* @param DevAddress Target device address: The device 7 bits address value
	621	* in datasheet must be shift at right before call interface
	622	* @param pData Pointer to data buffer
	623	* @param Size Amount of data to be sent
	624	* @param Timeout Timeout duration
	625	* @retval HAL status
	626	*/
	627	HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size, uint32_t Timeout)
	628	{
	629	uint32_t tickstart = 0U;
	630
	631	if (hi2c->State == HAL_I2C_STATE_READY)
	632	{
	633	/* Process Locked */
	634	__HAL_LOCK(hi2c);
	635
	636	/* Init tickstart for timeout management*/
	637	tickstart = HAL_GetTick();
	638
	639	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK)
	640	{
	641	return HAL_TIMEOUT;
	642	}
	643
	644	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	645	hi2c->Mode = HAL_I2C_MODE_MASTER;
	646	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	647
	648	/* Prepare transfer parameters */
	649	hi2c->pBuffPtr = pData;
	650	hi2c->XferCount = Size;
	651	hi2c->XferISR = NULL;
	652
	653	/* Send Slave Address */
	654	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	655	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	656	{
	657	hi2c->XferSize = MAX_NBYTE_SIZE;
	658	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE);
	659	}
	660	else
	661	{
	662	hi2c->XferSize = hi2c->XferCount;
	663	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE);
	664	}
	665
	666	while (hi2c->XferCount > 0U)
	667	{
	668	/* Wait until TXIS flag is set */
	669	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	670	{
	671	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	672	{
	673	return HAL_ERROR;
	674	}
	675	else
	676	{
	677	return HAL_TIMEOUT;
	678	}
	679	}
	680	/* Write data to TXDR */
	681	hi2c->Instance->TXDR = (*hi2c->pBuffPtr++);
	682	hi2c->XferCount--;
	683	hi2c->XferSize--;
	684
	685	if ((hi2c->XferSize == 0U) && (hi2c->XferCount != 0U))
	686	{
	687	/* Wait until TCR flag is set */
	688	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK)
	689	{
	690	return HAL_TIMEOUT;
	691	}
	692
	693	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	694	{
	695	hi2c->XferSize = MAX_NBYTE_SIZE;
	696	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	697	}
	698	else
	699	{
	700	hi2c->XferSize = hi2c->XferCount;
	701	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	702	}
	703	}
	704	}
	705
	706	/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
	707	/* Wait until STOPF flag is set */
	708	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	709	{
	710	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	711	{
	712	return HAL_ERROR;
	713	}
	714	else
	715	{
	716	return HAL_TIMEOUT;
	717	}
	718	}
	719
	720	/* Clear STOP Flag */
	721	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	722
	723	/* Clear Configuration Register 2 */
	724	I2C_RESET_CR2(hi2c);
	725
	726	hi2c->State = HAL_I2C_STATE_READY;
	727	hi2c->Mode = HAL_I2C_MODE_NONE;
	728
	729	/* Process Unlocked */
	730	__HAL_UNLOCK(hi2c);
	731
	732	return HAL_OK;
	733	}
	734	else
	735	{
	736	return HAL_BUSY;
	737	}
	738	}
	739
	740	/**
	741	* @brief Receives in master mode an amount of data in blocking mode.
	742	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	743	* the configuration information for the specified I2C.
	744	* @param DevAddress Target device address: The device 7 bits address value
	745	* in datasheet must be shift at right before call interface
	746	* @param pData Pointer to data buffer
	747	* @param Size Amount of data to be sent
	748	* @param Timeout Timeout duration
	749	* @retval HAL status
	750	*/
	751	HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size, uint32_t Timeout)
	752	{
	753	uint32_t tickstart = 0U;
	754
	755	if (hi2c->State == HAL_I2C_STATE_READY)
	756	{
	757	/* Process Locked */
	758	__HAL_LOCK(hi2c);
	759
	760	/* Init tickstart for timeout management*/
	761	tickstart = HAL_GetTick();
	762
	763	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK)
	764	{
	765	return HAL_TIMEOUT;
	766	}
	767
	768	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	769	hi2c->Mode = HAL_I2C_MODE_MASTER;
	770	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	771
	772	/* Prepare transfer parameters */
	773	hi2c->pBuffPtr = pData;
	774	hi2c->XferCount = Size;
	775	hi2c->XferISR = NULL;
	776
	777	/* Send Slave Address */
	778	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	779	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	780	{
	781	hi2c->XferSize = MAX_NBYTE_SIZE;
	782	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ);
	783	}
	784	else
	785	{
	786	hi2c->XferSize = hi2c->XferCount;
	787	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
	788	}
	789
	790	while (hi2c->XferCount > 0U)
	791	{
	792	/* Wait until RXNE flag is set */
	793	if (I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	794	{
	795	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	796	{
	797	return HAL_ERROR;
	798	}
	799	else
	800	{
	801	return HAL_TIMEOUT;
	802	}
	803	}
	804
	805	/* Read data from RXDR */
	806	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	807	hi2c->XferSize--;
	808	hi2c->XferCount--;
	809
	810	if ((hi2c->XferSize == 0U) && (hi2c->XferCount != 0U))
	811	{
	812	/* Wait until TCR flag is set */
	813	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK)
	814	{
	815	return HAL_TIMEOUT;
	816	}
	817
	818	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	819	{
	820	hi2c->XferSize = MAX_NBYTE_SIZE;
	821	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	822	}
	823	else
	824	{
	825	hi2c->XferSize = hi2c->XferCount;
	826	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	827	}
	828	}
	829	}
	830
	831	/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
	832	/* Wait until STOPF flag is set */
	833	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	834	{
	835	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	836	{
	837	return HAL_ERROR;
	838	}
	839	else
	840	{
	841	return HAL_TIMEOUT;
	842	}
	843	}
	844
	845	/* Clear STOP Flag */
	846	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	847
	848	/* Clear Configuration Register 2 */
	849	I2C_RESET_CR2(hi2c);
	850
	851	hi2c->State = HAL_I2C_STATE_READY;
	852	hi2c->Mode = HAL_I2C_MODE_NONE;
	853
	854	/* Process Unlocked */
	855	__HAL_UNLOCK(hi2c);
	856
	857	return HAL_OK;
	858	}
	859	else
	860	{
	861	return HAL_BUSY;
	862	}
	863	}
	864
	865	/**
	866	* @brief Transmits in slave mode an amount of data in blocking mode.
	867	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	868	* the configuration information for the specified I2C.
	869	* @param pData Pointer to data buffer
	870	* @param Size Amount of data to be sent
	871	* @param Timeout Timeout duration
	872	* @retval HAL status
	873	*/
	874	HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size, uint32_t Timeout)
	875	{
	876	uint32_t tickstart = 0U;
	877
	878	if (hi2c->State == HAL_I2C_STATE_READY)
	879	{
	880	if ((pData == NULL) \|\| (Size == 0U))
	881	{
	882	return HAL_ERROR;
	883	}
	884	/* Process Locked */
	885	__HAL_LOCK(hi2c);
	886
	887	/* Init tickstart for timeout management*/
	888	tickstart = HAL_GetTick();
	889
	890	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	891	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	892	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	893
	894	/* Prepare transfer parameters */
	895	hi2c->pBuffPtr = pData;
	896	hi2c->XferCount = Size;
	897	hi2c->XferISR = NULL;
	898
	899	/* Enable Address Acknowledge */
	900	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	901
	902	/* Wait until ADDR flag is set */
	903	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK)
	904	{
	905	/* Disable Address Acknowledge */
	906	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	907	return HAL_TIMEOUT;
	908	}
	909
	910	/* Clear ADDR flag */
	911	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	912
	913	/* If 10bit addressing mode is selected */
	914	if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT)
	915	{
	916	/* Wait until ADDR flag is set */
	917	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK)
	918	{
	919	/* Disable Address Acknowledge */
	920	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	921	return HAL_TIMEOUT;
	922	}
	923
	924	/* Clear ADDR flag */
	925	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	926	}
	927
	928	/* Wait until DIR flag is set Transmitter mode */
	929	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, RESET, Timeout, tickstart) != HAL_OK)
	930	{
	931	/* Disable Address Acknowledge */
	932	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	933	return HAL_TIMEOUT;
	934	}
	935
	936	while (hi2c->XferCount > 0U)
	937	{
	938	/* Wait until TXIS flag is set */
	939	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	940	{
	941	/* Disable Address Acknowledge */
	942	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	943
	944	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	945	{
	946	return HAL_ERROR;
	947	}
	948	else
	949	{
	950	return HAL_TIMEOUT;
	951	}
	952	}
	953
	954	/* Write data to TXDR */
	955	hi2c->Instance->TXDR = (*hi2c->pBuffPtr++);
	956	hi2c->XferCount--;
	957	}
	958
	959	/* Wait until STOP flag is set */
	960	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	961	{
	962	/* Disable Address Acknowledge */
	963	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	964
	965	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	966	{
	967	/* Normal use case for Transmitter mode */
	968	/* A NACK is generated to confirm the end of transfer */
	969	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	970	}
	971	else
	972	{
	973	return HAL_TIMEOUT;
	974	}
	975	}
	976
	977	/* Clear STOP flag */
	978	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	979
	980	/* Wait until BUSY flag is reset */
	981	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK)
	982	{
	983	/* Disable Address Acknowledge */
	984	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	985	return HAL_TIMEOUT;
	986	}
	987
	988	/* Disable Address Acknowledge */
	989	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	990
	991	hi2c->State = HAL_I2C_STATE_READY;
	992	hi2c->Mode = HAL_I2C_MODE_NONE;
	993
	994	/* Process Unlocked */
	995	__HAL_UNLOCK(hi2c);
	996
	997	return HAL_OK;
	998	}
	999	else
	1000	{
	1001	return HAL_BUSY;
	1002	}
	1003	}
	1004
	1005	/**
	1006	* @brief Receive in slave mode an amount of data in blocking mode
	1007	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1008	* the configuration information for the specified I2C.
	1009	* @param pData Pointer to data buffer
	1010	* @param Size Amount of data to be sent
	1011	* @param Timeout Timeout duration
	1012	* @retval HAL status
	1013	*/
	1014	HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size, uint32_t Timeout)
	1015	{
	1016	uint32_t tickstart = 0U;
	1017
	1018	if (hi2c->State == HAL_I2C_STATE_READY)
	1019	{
	1020	if ((pData == NULL) \|\| (Size == 0U))
	1021	{
	1022	return HAL_ERROR;
	1023	}
	1024	/* Process Locked */
	1025	__HAL_LOCK(hi2c);
	1026
	1027	/* Init tickstart for timeout management*/
	1028	tickstart = HAL_GetTick();
	1029
	1030	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1031	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	1032	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1033
	1034	/* Prepare transfer parameters */
	1035	hi2c->pBuffPtr = pData;
	1036	hi2c->XferCount = Size;
	1037	hi2c->XferISR = NULL;
	1038
	1039	/* Enable Address Acknowledge */
	1040	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	1041
	1042	/* Wait until ADDR flag is set */
	1043	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_ADDR, RESET, Timeout, tickstart) != HAL_OK)
	1044	{
	1045	/* Disable Address Acknowledge */
	1046	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1047	return HAL_TIMEOUT;
	1048	}
	1049
	1050	/* Clear ADDR flag */
	1051	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	1052
	1053	/* Wait until DIR flag is reset Receiver mode */
	1054	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_DIR, SET, Timeout, tickstart) != HAL_OK)
	1055	{
	1056	/* Disable Address Acknowledge */
	1057	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1058	return HAL_TIMEOUT;
	1059	}
	1060
	1061	while (hi2c->XferCount > 0U)
	1062	{
	1063	/* Wait until RXNE flag is set */
	1064	if (I2C_WaitOnRXNEFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	1065	{
	1066	/* Disable Address Acknowledge */
	1067	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1068
	1069	/* Store Last receive data if any */
	1070	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == SET)
	1071	{
	1072	/* Read data from RXDR */
	1073	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	1074	hi2c->XferCount--;
	1075	}
	1076
	1077	if (hi2c->ErrorCode == HAL_I2C_ERROR_TIMEOUT)
	1078	{
	1079	return HAL_TIMEOUT;
	1080	}
	1081	else
	1082	{
	1083	return HAL_ERROR;
	1084	}
	1085	}
	1086
	1087	/* Read data from RXDR */
	1088	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	1089	hi2c->XferCount--;
	1090	}
	1091
	1092	/* Wait until STOP flag is set */
	1093	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	1094	{
	1095	/* Disable Address Acknowledge */
	1096	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1097
	1098	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1099	{
	1100	return HAL_ERROR;
	1101	}
	1102	else
	1103	{
	1104	return HAL_TIMEOUT;
	1105	}
	1106	}
	1107
	1108	/* Clear STOP flag */
	1109	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	1110
	1111	/* Wait until BUSY flag is reset */
	1112	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, Timeout, tickstart) != HAL_OK)
	1113	{
	1114	/* Disable Address Acknowledge */
	1115	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1116	return HAL_TIMEOUT;
	1117	}
	1118
	1119	/* Disable Address Acknowledge */
	1120	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	1121
	1122	hi2c->State = HAL_I2C_STATE_READY;
	1123	hi2c->Mode = HAL_I2C_MODE_NONE;
	1124
	1125	/* Process Unlocked */
	1126	__HAL_UNLOCK(hi2c);
	1127
	1128	return HAL_OK;
	1129	}
	1130	else
	1131	{
	1132	return HAL_BUSY;
	1133	}
	1134	}
	1135
	1136	/**
	1137	* @brief Transmit in master mode an amount of data in non-blocking mode with Interrupt
	1138	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1139	* the configuration information for the specified I2C.
	1140	* @param DevAddress Target device address: The device 7 bits address value
	1141	* in datasheet must be shift at right before call interface
	1142	* @param pData Pointer to data buffer
	1143	* @param Size Amount of data to be sent
	1144	* @retval HAL status
	1145	*/
	1146	HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size)
	1147	{
	1148	uint32_t xfermode = 0U;
	1149
	1150	if (hi2c->State == HAL_I2C_STATE_READY)
	1151	{
	1152	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	1153	{
	1154	return HAL_BUSY;
	1155	}
	1156
	1157	/* Process Locked */
	1158	__HAL_LOCK(hi2c);
	1159
	1160	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	1161	hi2c->Mode = HAL_I2C_MODE_MASTER;
	1162	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1163
	1164	/* Prepare transfer parameters */
	1165	hi2c->pBuffPtr = pData;
	1166	hi2c->XferCount = Size;
	1167	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1168	hi2c->XferISR = I2C_Master_ISR_IT;
	1169
	1170	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1171	{
	1172	hi2c->XferSize = MAX_NBYTE_SIZE;
	1173	xfermode = I2C_RELOAD_MODE;
	1174	}
	1175	else
	1176	{
	1177	hi2c->XferSize = hi2c->XferCount;
	1178	xfermode = I2C_AUTOEND_MODE;
	1179	}
	1180
	1181	/* Send Slave Address */
	1182	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */
	1183	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_WRITE);
	1184
	1185	/* Process Unlocked */
	1186	__HAL_UNLOCK(hi2c);
	1187
	1188	/* Note : The I2C interrupts must be enabled after unlocking current process
	1189	to avoid the risk of I2C interrupt handle execution before current
	1190	process unlock */
	1191
	1192	/* Enable ERR, TC, STOP, NACK, TXI interrupt */
	1193	/* possible to enable all of these */
	1194	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1195	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
	1196
	1197	return HAL_OK;
	1198	}
	1199	else
	1200	{
	1201	return HAL_BUSY;
	1202	}
	1203	}
	1204
	1205	/**
	1206	* @brief Receive in master mode an amount of data in non-blocking mode with Interrupt
	1207	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1208	* the configuration information for the specified I2C.
	1209	* @param DevAddress Target device address: The device 7 bits address value
	1210	* in datasheet must be shift at right before call interface
	1211	* @param pData Pointer to data buffer
	1212	* @param Size Amount of data to be sent
	1213	* @retval HAL status
	1214	*/
	1215	HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size)
	1216	{
	1217	uint32_t xfermode = 0U;
	1218
	1219	if (hi2c->State == HAL_I2C_STATE_READY)
	1220	{
	1221	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	1222	{
	1223	return HAL_BUSY;
	1224	}
	1225
	1226	/* Process Locked */
	1227	__HAL_LOCK(hi2c);
	1228
	1229	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1230	hi2c->Mode = HAL_I2C_MODE_MASTER;
	1231	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1232
	1233	/* Prepare transfer parameters */
	1234	hi2c->pBuffPtr = pData;
	1235	hi2c->XferCount = Size;
	1236	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1237	hi2c->XferISR = I2C_Master_ISR_IT;
	1238
	1239	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1240	{
	1241	hi2c->XferSize = MAX_NBYTE_SIZE;
	1242	xfermode = I2C_RELOAD_MODE;
	1243	}
	1244	else
	1245	{
	1246	hi2c->XferSize = hi2c->XferCount;
	1247	xfermode = I2C_AUTOEND_MODE;
	1248	}
	1249
	1250	/* Send Slave Address */
	1251	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */
	1252	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ);
	1253
	1254	/* Process Unlocked */
	1255	__HAL_UNLOCK(hi2c);
	1256
	1257	/* Note : The I2C interrupts must be enabled after unlocking current process
	1258	to avoid the risk of I2C interrupt handle execution before current
	1259	process unlock */
	1260
	1261	/* Enable ERR, TC, STOP, NACK, RXI interrupt */
	1262	/* possible to enable all of these */
	1263	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1264	I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT);
	1265
	1266	return HAL_OK;
	1267	}
	1268	else
	1269	{
	1270	return HAL_BUSY;
	1271	}
	1272	}
	1273
	1274	/**
	1275	* @brief Transmit in slave mode an amount of data in non-blocking mode with Interrupt
	1276	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1277	* the configuration information for the specified I2C.
	1278	* @param pData Pointer to data buffer
	1279	* @param Size Amount of data to be sent
	1280	* @retval HAL status
	1281	*/
	1282	HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size)
	1283	{
	1284	if (hi2c->State == HAL_I2C_STATE_READY)
	1285	{
	1286	/* Process Locked */
	1287	__HAL_LOCK(hi2c);
	1288
	1289	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	1290	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	1291	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1292
	1293	/* Enable Address Acknowledge */
	1294	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	1295
	1296	/* Prepare transfer parameters */
	1297	hi2c->pBuffPtr = pData;
	1298	hi2c->XferCount = Size;
	1299	hi2c->XferSize = hi2c->XferCount;
	1300	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1301	hi2c->XferISR = I2C_Slave_ISR_IT;
	1302
	1303	/* Process Unlocked */
	1304	__HAL_UNLOCK(hi2c);
	1305
	1306	/* Note : The I2C interrupts must be enabled after unlocking current process
	1307	to avoid the risk of I2C interrupt handle execution before current
	1308	process unlock */
	1309
	1310	/* Enable ERR, TC, STOP, NACK, TXI interrupt */
	1311	/* possible to enable all of these */
	1312	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1313	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT \| I2C_XFER_LISTEN_IT);
	1314
	1315	return HAL_OK;
	1316	}
	1317	else
	1318	{
	1319	return HAL_BUSY;
	1320	}
	1321	}
	1322
	1323	/**
	1324	* @brief Receive in slave mode an amount of data in non-blocking mode with Interrupt
	1325	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1326	* the configuration information for the specified I2C.
	1327	* @param pData Pointer to data buffer
	1328	* @param Size Amount of data to be sent
	1329	* @retval HAL status
	1330	*/
	1331	HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size)
	1332	{
	1333	if (hi2c->State == HAL_I2C_STATE_READY)
	1334	{
	1335	/* Process Locked */
	1336	__HAL_LOCK(hi2c);
	1337
	1338	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1339	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	1340	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1341
	1342	/* Enable Address Acknowledge */
	1343	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	1344
	1345	/* Prepare transfer parameters */
	1346	hi2c->pBuffPtr = pData;
	1347	hi2c->XferCount = Size;
	1348	hi2c->XferSize = hi2c->XferCount;
	1349	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1350	hi2c->XferISR = I2C_Slave_ISR_IT;
	1351
	1352	/* Process Unlocked */
	1353	__HAL_UNLOCK(hi2c);
	1354
	1355	/* Note : The I2C interrupts must be enabled after unlocking current process
	1356	to avoid the risk of I2C interrupt handle execution before current
	1357	process unlock */
	1358
	1359	/* Enable ERR, TC, STOP, NACK, RXI interrupt */
	1360	/* possible to enable all of these */
	1361	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1362	I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT \| I2C_XFER_LISTEN_IT);
	1363
	1364	return HAL_OK;
	1365	}
	1366	else
	1367	{
	1368	return HAL_BUSY;
	1369	}
	1370	}
	1371
	1372	/**
	1373	* @brief Transmit in master mode an amount of data in non-blocking mode with DMA
	1374	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1375	* the configuration information for the specified I2C.
	1376	* @param DevAddress Target device address: The device 7 bits address value
	1377	* in datasheet must be shift at right before call interface
	1378	* @param pData Pointer to data buffer
	1379	* @param Size Amount of data to be sent
	1380	* @retval HAL status
	1381	*/
	1382	HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size)
	1383	{
	1384	uint32_t xfermode = 0U;
	1385
	1386	if (hi2c->State == HAL_I2C_STATE_READY)
	1387	{
	1388	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	1389	{
	1390	return HAL_BUSY;
	1391	}
	1392
	1393	/* Process Locked */
	1394	__HAL_LOCK(hi2c);
	1395
	1396	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	1397	hi2c->Mode = HAL_I2C_MODE_MASTER;
	1398	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1399
	1400	/* Prepare transfer parameters */
	1401	hi2c->pBuffPtr = pData;
	1402	hi2c->XferCount = Size;
	1403	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1404	hi2c->XferISR = I2C_Master_ISR_DMA;
	1405
	1406	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1407	{
	1408	hi2c->XferSize = MAX_NBYTE_SIZE;
	1409	xfermode = I2C_RELOAD_MODE;
	1410	}
	1411	else
	1412	{
	1413	hi2c->XferSize = hi2c->XferCount;
	1414	xfermode = I2C_AUTOEND_MODE;
	1415	}
	1416
	1417	if (hi2c->XferSize > 0U)
	1418	{
	1419	/* Set the I2C DMA transfer complete callback */
	1420	hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt;
	1421
	1422	/* Set the DMA error callback */
	1423	hi2c->hdmatx->XferErrorCallback = I2C_DMAError;
	1424
	1425	/* Set the unused DMA callbacks to NULL */
	1426	hi2c->hdmatx->XferHalfCpltCallback = NULL;
	1427	hi2c->hdmatx->XferAbortCallback = NULL;
	1428
	1429	/* Enable the DMA channel */
	1430	HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
	1431
	1432	/* Send Slave Address */
	1433	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	1434	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_WRITE);
	1435
	1436	/* Update XferCount value */
	1437	hi2c->XferCount -= hi2c->XferSize;
	1438
	1439	/* Process Unlocked */
	1440	__HAL_UNLOCK(hi2c);
	1441
	1442	/* Note : The I2C interrupts must be enabled after unlocking current process
	1443	to avoid the risk of I2C interrupt handle execution before current
	1444	process unlock */
	1445	/* Enable ERR and NACK interrupts */
	1446	I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT);
	1447
	1448	/* Enable DMA Request */
	1449	hi2c->Instance->CR1 \|= I2C_CR1_TXDMAEN;
	1450	}
	1451	else
	1452	{
	1453	/* Update Transfer ISR function pointer */
	1454	hi2c->XferISR = I2C_Master_ISR_IT;
	1455
	1456	/* Send Slave Address */
	1457	/* Set NBYTES to write and generate START condition */
	1458	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE);
	1459
	1460	/* Process Unlocked */
	1461	__HAL_UNLOCK(hi2c);
	1462
	1463	/* Note : The I2C interrupts must be enabled after unlocking current process
	1464	to avoid the risk of I2C interrupt handle execution before current
	1465	process unlock */
	1466	/* Enable ERR, TC, STOP, NACK, TXI interrupt */
	1467	/* possible to enable all of these */
	1468	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1469	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
	1470	}
	1471
	1472	return HAL_OK;
	1473	}
	1474	else
	1475	{
	1476	return HAL_BUSY;
	1477	}
	1478	}
	1479
	1480	/**
	1481	* @brief Receive in master mode an amount of data in non-blocking mode with DMA
	1482	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1483	* the configuration information for the specified I2C.
	1484	* @param DevAddress Target device address: The device 7 bits address value
	1485	* in datasheet must be shift at right before call interface
	1486	* @param pData Pointer to data buffer
	1487	* @param Size Amount of data to be sent
	1488	* @retval HAL status
	1489	*/
	1490	HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size)
	1491	{
	1492	uint32_t xfermode = 0U;
	1493
	1494	if (hi2c->State == HAL_I2C_STATE_READY)
	1495	{
	1496	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	1497	{
	1498	return HAL_BUSY;
	1499	}
	1500
	1501	/* Process Locked */
	1502	__HAL_LOCK(hi2c);
	1503
	1504	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1505	hi2c->Mode = HAL_I2C_MODE_MASTER;
	1506	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1507
	1508	/* Prepare transfer parameters */
	1509	hi2c->pBuffPtr = pData;
	1510	hi2c->XferCount = Size;
	1511	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1512	hi2c->XferISR = I2C_Master_ISR_DMA;
	1513
	1514	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1515	{
	1516	hi2c->XferSize = MAX_NBYTE_SIZE;
	1517	xfermode = I2C_RELOAD_MODE;
	1518	}
	1519	else
	1520	{
	1521	hi2c->XferSize = hi2c->XferCount;
	1522	xfermode = I2C_AUTOEND_MODE;
	1523	}
	1524
	1525	if (hi2c->XferSize > 0U)
	1526	{
	1527	/* Set the I2C DMA transfer complete callback */
	1528	hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt;
	1529
	1530	/* Set the DMA error callback */
	1531	hi2c->hdmarx->XferErrorCallback = I2C_DMAError;
	1532
	1533	/* Set the unused DMA callbacks to NULL */
	1534	hi2c->hdmarx->XferHalfCpltCallback = NULL;
	1535	hi2c->hdmarx->XferAbortCallback = NULL;
	1536
	1537	/* Enable the DMA channel */
	1538	HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
	1539
	1540	/* Send Slave Address */
	1541	/* Set NBYTES to read and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	1542	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ);
	1543
	1544	/* Update XferCount value */
	1545	hi2c->XferCount -= hi2c->XferSize;
	1546
	1547	/* Process Unlocked */
	1548	__HAL_UNLOCK(hi2c);
	1549
	1550	/* Note : The I2C interrupts must be enabled after unlocking current process
	1551	to avoid the risk of I2C interrupt handle execution before current
	1552	process unlock */
	1553	/* Enable ERR and NACK interrupts */
	1554	I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT);
	1555
	1556	/* Enable DMA Request */
	1557	hi2c->Instance->CR1 \|= I2C_CR1_RXDMAEN;
	1558	}
	1559	else
	1560	{
	1561	/* Update Transfer ISR function pointer */
	1562	hi2c->XferISR = I2C_Master_ISR_IT;
	1563
	1564	/* Send Slave Address */
	1565	/* Set NBYTES to read and generate START condition */
	1566	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
	1567
	1568	/* Process Unlocked */
	1569	__HAL_UNLOCK(hi2c);
	1570
	1571	/* Note : The I2C interrupts must be enabled after unlocking current process
	1572	to avoid the risk of I2C interrupt handle execution before current
	1573	process unlock */
	1574	/* Enable ERR, TC, STOP, NACK, TXI interrupt */
	1575	/* possible to enable all of these */
	1576	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	1577	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
	1578	}
	1579	return HAL_OK;
	1580	}
	1581	else
	1582	{
	1583	return HAL_BUSY;
	1584	}
	1585	}
	1586
	1587	/**
	1588	* @brief Transmit in slave mode an amount of data in non-blocking mode with DMA
	1589	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1590	* the configuration information for the specified I2C.
	1591	* @param pData Pointer to data buffer
	1592	* @param Size Amount of data to be sent
	1593	* @retval HAL status
	1594	*/
	1595	HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size)
	1596	{
	1597	if (hi2c->State == HAL_I2C_STATE_READY)
	1598	{
	1599	if ((pData == NULL) \|\| (Size == 0U))
	1600	{
	1601	return HAL_ERROR;
	1602	}
	1603	/* Process Locked */
	1604	__HAL_LOCK(hi2c);
	1605
	1606	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	1607	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	1608	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1609
	1610	/* Prepare transfer parameters */
	1611	hi2c->pBuffPtr = pData;
	1612	hi2c->XferCount = Size;
	1613	hi2c->XferSize = hi2c->XferCount;
	1614	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1615	hi2c->XferISR = I2C_Slave_ISR_DMA;
	1616
	1617	/* Set the I2C DMA transfer complete callback */
	1618	hi2c->hdmatx->XferCpltCallback = I2C_DMASlaveTransmitCplt;
	1619
	1620	/* Set the DMA error callback */
	1621	hi2c->hdmatx->XferErrorCallback = I2C_DMAError;
	1622
	1623	/* Set the unused DMA callbacks to NULL */
	1624	hi2c->hdmatx->XferHalfCpltCallback = NULL;
	1625	hi2c->hdmatx->XferAbortCallback = NULL;
	1626
	1627	/* Enable the DMA channel */
	1628	HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
	1629
	1630	/* Enable Address Acknowledge */
	1631	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	1632
	1633	/* Process Unlocked */
	1634	__HAL_UNLOCK(hi2c);
	1635
	1636	/* Note : The I2C interrupts must be enabled after unlocking current process
	1637	to avoid the risk of I2C interrupt handle execution before current
	1638	process unlock */
	1639	/* Enable ERR, STOP, NACK, ADDR interrupts */
	1640	I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	1641
	1642	/* Enable DMA Request */
	1643	hi2c->Instance->CR1 \|= I2C_CR1_TXDMAEN;
	1644
	1645	return HAL_OK;
	1646	}
	1647	else
	1648	{
	1649	return HAL_BUSY;
	1650	}
	1651	}
	1652
	1653	/**
	1654	* @brief Receive in slave mode an amount of data in non-blocking mode with DMA
	1655	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1656	* the configuration information for the specified I2C.
	1657	* @param pData Pointer to data buffer
	1658	* @param Size Amount of data to be sent
	1659	* @retval HAL status
	1660	*/
	1661	HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size)
	1662	{
	1663	if (hi2c->State == HAL_I2C_STATE_READY)
	1664	{
	1665	if ((pData == NULL) \|\| (Size == 0U))
	1666	{
	1667	return HAL_ERROR;
	1668	}
	1669	/* Process Locked */
	1670	__HAL_LOCK(hi2c);
	1671
	1672	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1673	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	1674	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1675
	1676	/* Prepare transfer parameters */
	1677	hi2c->pBuffPtr = pData;
	1678	hi2c->XferCount = Size;
	1679	hi2c->XferSize = hi2c->XferCount;
	1680	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	1681	hi2c->XferISR = I2C_Slave_ISR_DMA;
	1682
	1683	/* Set the I2C DMA transfer complete callback */
	1684	hi2c->hdmarx->XferCpltCallback = I2C_DMASlaveReceiveCplt;
	1685
	1686	/* Set the DMA error callback */
	1687	hi2c->hdmarx->XferErrorCallback = I2C_DMAError;
	1688
	1689	/* Set the unused DMA callbacks to NULL */
	1690	hi2c->hdmarx->XferHalfCpltCallback = NULL;
	1691	hi2c->hdmarx->XferAbortCallback = NULL;
	1692
	1693	/* Enable the DMA channel */
	1694	HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
	1695
	1696	/* Enable Address Acknowledge */
	1697	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	1698
	1699	/* Process Unlocked */
	1700	__HAL_UNLOCK(hi2c);
	1701
	1702	/* Note : The I2C interrupts must be enabled after unlocking current process
	1703	to avoid the risk of I2C interrupt handle execution before current
	1704	process unlock */
	1705	/* Enable ERR, STOP, NACK, ADDR interrupts */
	1706	I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	1707
	1708	/* Enable DMA Request */
	1709	hi2c->Instance->CR1 \|= I2C_CR1_RXDMAEN;
	1710
	1711	return HAL_OK;
	1712	}
	1713	else
	1714	{
	1715	return HAL_BUSY;
	1716	}
	1717	}
	1718	/**
	1719	* @brief Write an amount of data in blocking mode to a specific memory address
	1720	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1721	* the configuration information for the specified I2C.
	1722	* @param DevAddress Target device address: The device 7 bits address value
	1723	* in datasheet must be shift at right before call interface
	1724	* @param MemAddress Internal memory address
	1725	* @param MemAddSize Size of internal memory address
	1726	* @param pData Pointer to data buffer
	1727	* @param Size Amount of data to be sent
	1728	* @param Timeout Timeout duration
	1729	* @retval HAL status
	1730	*/
	1731	HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size, uint32_t Timeout)
	1732	{
	1733	uint32_t tickstart = 0U;
	1734
	1735	/* Check the parameters */
	1736	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	1737
	1738	if (hi2c->State == HAL_I2C_STATE_READY)
	1739	{
	1740	if ((pData == NULL) \|\| (Size == 0U))
	1741	{
	1742	return HAL_ERROR;
	1743	}
	1744
	1745	/* Process Locked */
	1746	__HAL_LOCK(hi2c);
	1747
	1748	/* Init tickstart for timeout management*/
	1749	tickstart = HAL_GetTick();
	1750
	1751	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK)
	1752	{
	1753	return HAL_TIMEOUT;
	1754	}
	1755
	1756	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	1757	hi2c->Mode = HAL_I2C_MODE_MEM;
	1758	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1759
	1760	/* Prepare transfer parameters */
	1761	hi2c->pBuffPtr = pData;
	1762	hi2c->XferCount = Size;
	1763	hi2c->XferISR = NULL;
	1764
	1765	/* Send Slave Address and Memory Address */
	1766	if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK)
	1767	{
	1768	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1769	{
	1770	/* Process Unlocked */
	1771	__HAL_UNLOCK(hi2c);
	1772	return HAL_ERROR;
	1773	}
	1774	else
	1775	{
	1776	/* Process Unlocked */
	1777	__HAL_UNLOCK(hi2c);
	1778	return HAL_TIMEOUT;
	1779	}
	1780	}
	1781
	1782	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE */
	1783	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1784	{
	1785	hi2c->XferSize = MAX_NBYTE_SIZE;
	1786	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	1787	}
	1788	else
	1789	{
	1790	hi2c->XferSize = hi2c->XferCount;
	1791	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	1792	}
	1793
	1794	do
	1795	{
	1796	/* Wait until TXIS flag is set */
	1797	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	1798	{
	1799	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1800	{
	1801	return HAL_ERROR;
	1802	}
	1803	else
	1804	{
	1805	return HAL_TIMEOUT;
	1806	}
	1807	}
	1808
	1809	/* Write data to TXDR */
	1810	hi2c->Instance->TXDR = (*hi2c->pBuffPtr++);
	1811	hi2c->XferCount--;
	1812	hi2c->XferSize--;
	1813
	1814	if ((hi2c->XferSize == 0U) && (hi2c->XferCount != 0U))
	1815	{
	1816	/* Wait until TCR flag is set */
	1817	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK)
	1818	{
	1819	return HAL_TIMEOUT;
	1820	}
	1821
	1822	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1823	{
	1824	hi2c->XferSize = MAX_NBYTE_SIZE;
	1825	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	1826	}
	1827	else
	1828	{
	1829	hi2c->XferSize = hi2c->XferCount;
	1830	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	1831	}
	1832	}
	1833
	1834	}
	1835	while (hi2c->XferCount > 0U);
	1836
	1837	/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
	1838	/* Wait until STOPF flag is reset */
	1839	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	1840	{
	1841	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1842	{
	1843	return HAL_ERROR;
	1844	}
	1845	else
	1846	{
	1847	return HAL_TIMEOUT;
	1848	}
	1849	}
	1850
	1851	/* Clear STOP Flag */
	1852	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	1853
	1854	/* Clear Configuration Register 2 */
	1855	I2C_RESET_CR2(hi2c);
	1856
	1857	hi2c->State = HAL_I2C_STATE_READY;
	1858	hi2c->Mode = HAL_I2C_MODE_NONE;
	1859
	1860	/* Process Unlocked */
	1861	__HAL_UNLOCK(hi2c);
	1862
	1863	return HAL_OK;
	1864	}
	1865	else
	1866	{
	1867	return HAL_BUSY;
	1868	}
	1869	}
	1870
	1871	/**
	1872	* @brief Read an amount of data in blocking mode from a specific memory address
	1873	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	1874	* the configuration information for the specified I2C.
	1875	* @param DevAddress Target device address: The device 7 bits address value
	1876	* in datasheet must be shift at right before call interface
	1877	* @param MemAddress Internal memory address
	1878	* @param MemAddSize Size of internal memory address
	1879	* @param pData Pointer to data buffer
	1880	* @param Size Amount of data to be sent
	1881	* @param Timeout Timeout duration
	1882	* @retval HAL status
	1883	*/
	1884	HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size, uint32_t Timeout)
	1885	{
	1886	uint32_t tickstart = 0U;
	1887
	1888	/* Check the parameters */
	1889	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	1890
	1891	if (hi2c->State == HAL_I2C_STATE_READY)
	1892	{
	1893	if ((pData == NULL) \|\| (Size == 0U))
	1894	{
	1895	return HAL_ERROR;
	1896	}
	1897
	1898	/* Process Locked */
	1899	__HAL_LOCK(hi2c);
	1900
	1901	/* Init tickstart for timeout management*/
	1902	tickstart = HAL_GetTick();
	1903
	1904	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_BUSY, SET, I2C_TIMEOUT_BUSY, tickstart) != HAL_OK)
	1905	{
	1906	return HAL_TIMEOUT;
	1907	}
	1908
	1909	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	1910	hi2c->Mode = HAL_I2C_MODE_MEM;
	1911	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	1912
	1913	/* Prepare transfer parameters */
	1914	hi2c->pBuffPtr = pData;
	1915	hi2c->XferCount = Size;
	1916	hi2c->XferISR = NULL;
	1917
	1918	/* Send Slave Address and Memory Address */
	1919	if (I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, Timeout, tickstart) != HAL_OK)
	1920	{
	1921	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1922	{
	1923	/* Process Unlocked */
	1924	__HAL_UNLOCK(hi2c);
	1925	return HAL_ERROR;
	1926	}
	1927	else
	1928	{
	1929	/* Process Unlocked */
	1930	__HAL_UNLOCK(hi2c);
	1931	return HAL_TIMEOUT;
	1932	}
	1933	}
	1934
	1935	/* Send Slave Address */
	1936	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	1937	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1938	{
	1939	hi2c->XferSize = MAX_NBYTE_SIZE;
	1940	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ);
	1941	}
	1942	else
	1943	{
	1944	hi2c->XferSize = hi2c->XferCount;
	1945	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
	1946	}
	1947
	1948	do
	1949	{
	1950	/* Wait until RXNE flag is set */
	1951	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_RXNE, RESET, Timeout, tickstart) != HAL_OK)
	1952	{
	1953	return HAL_TIMEOUT;
	1954	}
	1955
	1956	/* Read data from RXDR */
	1957	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	1958	hi2c->XferSize--;
	1959	hi2c->XferCount--;
	1960
	1961	if ((hi2c->XferSize == 0U) && (hi2c->XferCount != 0U))
	1962	{
	1963	/* Wait until TCR flag is set */
	1964	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, tickstart) != HAL_OK)
	1965	{
	1966	return HAL_TIMEOUT;
	1967	}
	1968
	1969	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	1970	{
	1971	hi2c->XferSize = MAX_NBYTE_SIZE;
	1972	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	1973	}
	1974	else
	1975	{
	1976	hi2c->XferSize = hi2c->XferCount;
	1977	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	1978	}
	1979	}
	1980	}
	1981	while (hi2c->XferCount > 0U);
	1982
	1983	/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
	1984	/* Wait until STOPF flag is reset */
	1985	if (I2C_WaitOnSTOPFlagUntilTimeout(hi2c, Timeout, tickstart) != HAL_OK)
	1986	{
	1987	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	1988	{
	1989	return HAL_ERROR;
	1990	}
	1991	else
	1992	{
	1993	return HAL_TIMEOUT;
	1994	}
	1995	}
	1996
	1997	/* Clear STOP Flag */
	1998	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	1999
	2000	/* Clear Configuration Register 2 */
	2001	I2C_RESET_CR2(hi2c);
	2002
	2003	hi2c->State = HAL_I2C_STATE_READY;
	2004	hi2c->Mode = HAL_I2C_MODE_NONE;
	2005
	2006	/* Process Unlocked */
	2007	__HAL_UNLOCK(hi2c);
	2008
	2009	return HAL_OK;
	2010	}
	2011	else
	2012	{
	2013	return HAL_BUSY;
	2014	}
	2015	}
	2016	/**
	2017	* @brief Write an amount of data in non-blocking mode with Interrupt to a specific memory address
	2018	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2019	* the configuration information for the specified I2C.
	2020	* @param DevAddress Target device address: The device 7 bits address value
	2021	* in datasheet must be shift at right before call interface
	2022	* @param MemAddress Internal memory address
	2023	* @param MemAddSize Size of internal memory address
	2024	* @param pData Pointer to data buffer
	2025	* @param Size Amount of data to be sent
	2026	* @retval HAL status
	2027	*/
	2028	HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size)
	2029	{
	2030	uint32_t tickstart = 0U;
	2031	uint32_t xfermode = 0U;
	2032
	2033	/* Check the parameters */
	2034	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	2035
	2036	if (hi2c->State == HAL_I2C_STATE_READY)
	2037	{
	2038	if ((pData == NULL) \|\| (Size == 0U))
	2039	{
	2040	return HAL_ERROR;
	2041	}
	2042
	2043	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	2044	{
	2045	return HAL_BUSY;
	2046	}
	2047
	2048	/* Process Locked */
	2049	__HAL_LOCK(hi2c);
	2050
	2051	/* Init tickstart for timeout management*/
	2052	tickstart = HAL_GetTick();
	2053
	2054	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	2055	hi2c->Mode = HAL_I2C_MODE_MEM;
	2056	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2057
	2058	/* Prepare transfer parameters */
	2059	hi2c->pBuffPtr = pData;
	2060	hi2c->XferCount = Size;
	2061	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	2062	hi2c->XferISR = I2C_Master_ISR_IT;
	2063
	2064	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2065	{
	2066	hi2c->XferSize = MAX_NBYTE_SIZE;
	2067	xfermode = I2C_RELOAD_MODE;
	2068	}
	2069	else
	2070	{
	2071	hi2c->XferSize = hi2c->XferCount;
	2072	xfermode = I2C_AUTOEND_MODE;
	2073	}
	2074
	2075	/* Send Slave Address and Memory Address */
	2076	if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
	2077	{
	2078	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	2079	{
	2080	/* Process Unlocked */
	2081	__HAL_UNLOCK(hi2c);
	2082	return HAL_ERROR;
	2083	}
	2084	else
	2085	{
	2086	/* Process Unlocked */
	2087	__HAL_UNLOCK(hi2c);
	2088	return HAL_TIMEOUT;
	2089	}
	2090	}
	2091
	2092	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	2093	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP);
	2094
	2095	/* Process Unlocked */
	2096	__HAL_UNLOCK(hi2c);
	2097
	2098	/* Note : The I2C interrupts must be enabled after unlocking current process
	2099	to avoid the risk of I2C interrupt handle execution before current
	2100	process unlock */
	2101
	2102	/* Enable ERR, TC, STOP, NACK, TXI interrupt */
	2103	/* possible to enable all of these */
	2104	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	2105	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
	2106
	2107	return HAL_OK;
	2108	}
	2109	else
	2110	{
	2111	return HAL_BUSY;
	2112	}
	2113	}
	2114
	2115	/**
	2116	* @brief Read an amount of data in non-blocking mode with Interrupt from a specific memory address
	2117	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2118	* the configuration information for the specified I2C.
	2119	* @param DevAddress Target device address: The device 7 bits address value
	2120	* in datasheet must be shift at right before call interface
	2121	* @param MemAddress Internal memory address
	2122	* @param MemAddSize Size of internal memory address
	2123	* @param pData Pointer to data buffer
	2124	* @param Size Amount of data to be sent
	2125	* @retval HAL status
	2126	*/
	2127	HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size)
	2128	{
	2129	uint32_t tickstart = 0U;
	2130	uint32_t xfermode = 0U;
	2131
	2132	/* Check the parameters */
	2133	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	2134
	2135	if (hi2c->State == HAL_I2C_STATE_READY)
	2136	{
	2137	if ((pData == NULL) \|\| (Size == 0U))
	2138	{
	2139	return HAL_ERROR;
	2140	}
	2141
	2142	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	2143	{
	2144	return HAL_BUSY;
	2145	}
	2146
	2147	/* Process Locked */
	2148	__HAL_LOCK(hi2c);
	2149
	2150	/* Init tickstart for timeout management*/
	2151	tickstart = HAL_GetTick();
	2152
	2153	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	2154	hi2c->Mode = HAL_I2C_MODE_MEM;
	2155	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2156
	2157	/* Prepare transfer parameters */
	2158	hi2c->pBuffPtr = pData;
	2159	hi2c->XferCount = Size;
	2160	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	2161	hi2c->XferISR = I2C_Master_ISR_IT;
	2162
	2163	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2164	{
	2165	hi2c->XferSize = MAX_NBYTE_SIZE;
	2166	xfermode = I2C_RELOAD_MODE;
	2167	}
	2168	else
	2169	{
	2170	hi2c->XferSize = hi2c->XferCount;
	2171	xfermode = I2C_AUTOEND_MODE;
	2172	}
	2173
	2174	/* Send Slave Address and Memory Address */
	2175	if (I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
	2176	{
	2177	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	2178	{
	2179	/* Process Unlocked */
	2180	__HAL_UNLOCK(hi2c);
	2181	return HAL_ERROR;
	2182	}
	2183	else
	2184	{
	2185	/* Process Unlocked */
	2186	__HAL_UNLOCK(hi2c);
	2187	return HAL_TIMEOUT;
	2188	}
	2189	}
	2190
	2191	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	2192	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ);
	2193
	2194	/* Process Unlocked */
	2195	__HAL_UNLOCK(hi2c);
	2196
	2197	/* Note : The I2C interrupts must be enabled after unlocking current process
	2198	to avoid the risk of I2C interrupt handle execution before current
	2199	process unlock */
	2200
	2201	/* Enable ERR, TC, STOP, NACK, RXI interrupt */
	2202	/* possible to enable all of these */
	2203	/* I2C_IT_ERRI \| I2C_IT_TCI\| I2C_IT_STOPI\| I2C_IT_NACKI \| I2C_IT_ADDRI \| I2C_IT_RXI \| I2C_IT_TXI */
	2204	I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT);
	2205
	2206	return HAL_OK;
	2207	}
	2208	else
	2209	{
	2210	return HAL_BUSY;
	2211	}
	2212	}
	2213	/**
	2214	* @brief Write an amount of data in non-blocking mode with DMA to a specific memory address
	2215	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2216	* the configuration information for the specified I2C.
	2217	* @param DevAddress Target device address: The device 7 bits address value
	2218	* in datasheet must be shift at right before call interface
	2219	* @param MemAddress Internal memory address
	2220	* @param MemAddSize Size of internal memory address
	2221	* @param pData Pointer to data buffer
	2222	* @param Size Amount of data to be sent
	2223	* @retval HAL status
	2224	*/
	2225	HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size)
	2226	{
	2227	uint32_t tickstart = 0U;
	2228	uint32_t xfermode = 0U;
	2229
	2230	/* Check the parameters */
	2231	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	2232
	2233	if (hi2c->State == HAL_I2C_STATE_READY)
	2234	{
	2235	if ((pData == NULL) \|\| (Size == 0U))
	2236	{
	2237	return HAL_ERROR;
	2238	}
	2239
	2240	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	2241	{
	2242	return HAL_BUSY;
	2243	}
	2244
	2245	/* Process Locked */
	2246	__HAL_LOCK(hi2c);
	2247
	2248	/* Init tickstart for timeout management*/
	2249	tickstart = HAL_GetTick();
	2250
	2251	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	2252	hi2c->Mode = HAL_I2C_MODE_MEM;
	2253	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2254
	2255	/* Prepare transfer parameters */
	2256	hi2c->pBuffPtr = pData;
	2257	hi2c->XferCount = Size;
	2258	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	2259	hi2c->XferISR = I2C_Master_ISR_DMA;
	2260
	2261	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2262	{
	2263	hi2c->XferSize = MAX_NBYTE_SIZE;
	2264	xfermode = I2C_RELOAD_MODE;
	2265	}
	2266	else
	2267	{
	2268	hi2c->XferSize = hi2c->XferCount;
	2269	xfermode = I2C_AUTOEND_MODE;
	2270	}
	2271
	2272	/* Send Slave Address and Memory Address */
	2273	if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
	2274	{
	2275	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	2276	{
	2277	/* Process Unlocked */
	2278	__HAL_UNLOCK(hi2c);
	2279	return HAL_ERROR;
	2280	}
	2281	else
	2282	{
	2283	/* Process Unlocked */
	2284	__HAL_UNLOCK(hi2c);
	2285	return HAL_TIMEOUT;
	2286	}
	2287	}
	2288
	2289	/* Set the I2C DMA transfer complete callback */
	2290	hi2c->hdmatx->XferCpltCallback = I2C_DMAMasterTransmitCplt;
	2291
	2292	/* Set the DMA error callback */
	2293	hi2c->hdmatx->XferErrorCallback = I2C_DMAError;
	2294
	2295	/* Set the unused DMA callbacks to NULL */
	2296	hi2c->hdmatx->XferHalfCpltCallback = NULL;
	2297	hi2c->hdmatx->XferAbortCallback = NULL;
	2298
	2299	/* Enable the DMA channel */
	2300	HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
	2301
	2302	/* Send Slave Address */
	2303	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	2304	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP);
	2305
	2306	/* Update XferCount value */
	2307	hi2c->XferCount -= hi2c->XferSize;
	2308
	2309	/* Process Unlocked */
	2310	__HAL_UNLOCK(hi2c);
	2311
	2312	/* Note : The I2C interrupts must be enabled after unlocking current process
	2313	to avoid the risk of I2C interrupt handle execution before current
	2314	process unlock */
	2315	/* Enable ERR and NACK interrupts */
	2316	I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT);
	2317
	2318	/* Enable DMA Request */
	2319	hi2c->Instance->CR1 \|= I2C_CR1_TXDMAEN;
	2320
	2321	return HAL_OK;
	2322	}
	2323	else
	2324	{
	2325	return HAL_BUSY;
	2326	}
	2327	}
	2328
	2329	/**
	2330	* @brief Reads an amount of data in non-blocking mode with DMA from a specific memory address.
	2331	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2332	* the configuration information for the specified I2C.
	2333	* @param DevAddress Target device address: The device 7 bits address value
	2334	* in datasheet must be shift at right before call interface
	2335	* @param MemAddress Internal memory address
	2336	* @param MemAddSize Size of internal memory address
	2337	* @param pData Pointer to data buffer
	2338	* @param Size Amount of data to be read
	2339	* @retval HAL status
	2340	*/
	2341	HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t pData, uint16_t Size)
	2342	{
	2343	uint32_t tickstart = 0U;
	2344	uint32_t xfermode = 0U;
	2345
	2346	/* Check the parameters */
	2347	assert_param(IS_I2C_MEMADD_SIZE(MemAddSize));
	2348
	2349	if (hi2c->State == HAL_I2C_STATE_READY)
	2350	{
	2351	if ((pData == NULL) \|\| (Size == 0U))
	2352	{
	2353	return HAL_ERROR;
	2354	}
	2355
	2356	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	2357	{
	2358	return HAL_BUSY;
	2359	}
	2360
	2361	/* Process Locked */
	2362	__HAL_LOCK(hi2c);
	2363
	2364	/* Init tickstart for timeout management*/
	2365	tickstart = HAL_GetTick();
	2366
	2367	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	2368	hi2c->Mode = HAL_I2C_MODE_MEM;
	2369	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2370
	2371	/* Prepare transfer parameters */
	2372	hi2c->pBuffPtr = pData;
	2373	hi2c->XferCount = Size;
	2374	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	2375	hi2c->XferISR = I2C_Master_ISR_DMA;
	2376
	2377	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2378	{
	2379	hi2c->XferSize = MAX_NBYTE_SIZE;
	2380	xfermode = I2C_RELOAD_MODE;
	2381	}
	2382	else
	2383	{
	2384	hi2c->XferSize = hi2c->XferCount;
	2385	xfermode = I2C_AUTOEND_MODE;
	2386	}
	2387
	2388	/* Send Slave Address and Memory Address */
	2389	if (I2C_RequestMemoryRead(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
	2390	{
	2391	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	2392	{
	2393	/* Process Unlocked */
	2394	__HAL_UNLOCK(hi2c);
	2395	return HAL_ERROR;
	2396	}
	2397	else
	2398	{
	2399	/* Process Unlocked */
	2400	__HAL_UNLOCK(hi2c);
	2401	return HAL_TIMEOUT;
	2402	}
	2403	}
	2404
	2405	/* Set the I2C DMA transfer complete callback */
	2406	hi2c->hdmarx->XferCpltCallback = I2C_DMAMasterReceiveCplt;
	2407
	2408	/* Set the DMA error callback */
	2409	hi2c->hdmarx->XferErrorCallback = I2C_DMAError;
	2410
	2411	/* Set the unused DMA callbacks to NULL */
	2412	hi2c->hdmarx->XferHalfCpltCallback = NULL;
	2413	hi2c->hdmarx->XferAbortCallback = NULL;
	2414
	2415	/* Enable the DMA channel */
	2416	HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
	2417
	2418	/* Set NBYTES to write and reload if hi2c->XferCount > MAX_NBYTE_SIZE and generate RESTART */
	2419	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, I2C_GENERATE_START_READ);
	2420
	2421	/* Update XferCount value */
	2422	hi2c->XferCount -= hi2c->XferSize;
	2423
	2424	/* Process Unlocked */
	2425	__HAL_UNLOCK(hi2c);
	2426
	2427	/* Enable DMA Request */
	2428	hi2c->Instance->CR1 \|= I2C_CR1_RXDMAEN;
	2429
	2430	/* Note : The I2C interrupts must be enabled after unlocking current process
	2431	to avoid the risk of I2C interrupt handle execution before current
	2432	process unlock */
	2433	/* Enable ERR and NACK interrupts */
	2434	I2C_Enable_IRQ(hi2c, I2C_XFER_ERROR_IT);
	2435
	2436	return HAL_OK;
	2437	}
	2438	else
	2439	{
	2440	return HAL_BUSY;
	2441	}
	2442	}
	2443
	2444	/**
	2445	* @brief Checks if target device is ready for communication.
	2446	* @note This function is used with Memory devices
	2447	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2448	* the configuration information for the specified I2C.
	2449	* @param DevAddress Target device address: The device 7 bits address value
	2450	* in datasheet must be shift at right before call interface
	2451	* @param Trials Number of trials
	2452	* @param Timeout Timeout duration
	2453	* @retval HAL status
	2454	*/
	2455	HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout)
	2456	{
	2457	uint32_t tickstart = 0U;
	2458
	2459	__IO uint32_t I2C_Trials = 0U;
	2460
	2461	if (hi2c->State == HAL_I2C_STATE_READY)
	2462	{
	2463	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_BUSY) == SET)
	2464	{
	2465	return HAL_BUSY;
	2466	}
	2467
	2468	/* Process Locked */
	2469	__HAL_LOCK(hi2c);
	2470
	2471	hi2c->State = HAL_I2C_STATE_BUSY;
	2472	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2473
	2474	do
	2475	{
	2476	/* Generate Start */
	2477	hi2c->Instance->CR2 = I2C_GENERATE_START(hi2c->Init.AddressingMode, DevAddress);
	2478
	2479	/* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
	2480	/* Wait until STOPF flag is set or a NACK flag is set*/
	2481	tickstart = HAL_GetTick();
	2482	while ((__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET) && (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == RESET) && (hi2c->State != HAL_I2C_STATE_TIMEOUT))
	2483	{
	2484	if (Timeout != HAL_MAX_DELAY)
	2485	{
	2486	if ((Timeout == 0U) \|\| ((HAL_GetTick() - tickstart) > Timeout))
	2487	{
	2488	/* Device is ready */
	2489	hi2c->State = HAL_I2C_STATE_READY;
	2490	/* Process Unlocked */
	2491	__HAL_UNLOCK(hi2c);
	2492	return HAL_TIMEOUT;
	2493	}
	2494	}
	2495	}
	2496
	2497	/* Check if the NACKF flag has not been set */
	2498	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == RESET)
	2499	{
	2500	/* Wait until STOPF flag is reset */
	2501	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK)
	2502	{
	2503	return HAL_TIMEOUT;
	2504	}
	2505
	2506	/* Clear STOP Flag */
	2507	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	2508
	2509	/* Device is ready */
	2510	hi2c->State = HAL_I2C_STATE_READY;
	2511
	2512	/* Process Unlocked */
	2513	__HAL_UNLOCK(hi2c);
	2514
	2515	return HAL_OK;
	2516	}
	2517	else
	2518	{
	2519	/* Wait until STOPF flag is reset */
	2520	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK)
	2521	{
	2522	return HAL_TIMEOUT;
	2523	}
	2524
	2525	/* Clear NACK Flag */
	2526	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	2527
	2528	/* Clear STOP Flag, auto generated with autoend*/
	2529	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	2530	}
	2531
	2532	/* Check if the maximum allowed number of trials has been reached */
	2533	if (I2C_Trials++ == Trials)
	2534	{
	2535	/* Generate Stop */
	2536	hi2c->Instance->CR2 \|= I2C_CR2_STOP;
	2537
	2538	/* Wait until STOPF flag is reset */
	2539	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_STOPF, RESET, Timeout, tickstart) != HAL_OK)
	2540	{
	2541	return HAL_TIMEOUT;
	2542	}
	2543
	2544	/* Clear STOP Flag */
	2545	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	2546	}
	2547	}
	2548	while (I2C_Trials < Trials);
	2549
	2550	hi2c->State = HAL_I2C_STATE_READY;
	2551
	2552	/* Process Unlocked */
	2553	__HAL_UNLOCK(hi2c);
	2554
	2555	return HAL_TIMEOUT;
	2556	}
	2557	else
	2558	{
	2559	return HAL_BUSY;
	2560	}
	2561	}
	2562
	2563	/**
	2564	* @brief Sequential transmit in master I2C mode an amount of data in non-blocking mode with Interrupt.
	2565	* @note This interface allow to manage repeated start condition when a direction change during transfer
	2566	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2567	* the configuration information for the specified I2C.
	2568	* @param DevAddress Target device address: The device 7 bits address value
	2569	* in datasheet must be shift at right before call interface
	2570	* @param pData Pointer to data buffer
	2571	* @param Size Amount of data to be sent
	2572	* @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS
	2573	* @retval HAL status
	2574	*/
	2575	HAL_StatusTypeDef HAL_I2C_Master_Sequential_Transmit_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size, uint32_t XferOptions)
	2576	{
	2577	uint32_t xfermode = 0U;
	2578	uint32_t xferrequest = I2C_GENERATE_START_WRITE;
	2579
	2580	/* Check the parameters */
	2581	assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions));
	2582
	2583	if (hi2c->State == HAL_I2C_STATE_READY)
	2584	{
	2585	/* Process Locked */
	2586	__HAL_LOCK(hi2c);
	2587
	2588	hi2c->State = HAL_I2C_STATE_BUSY_TX;
	2589	hi2c->Mode = HAL_I2C_MODE_MASTER;
	2590	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2591
	2592	/* Prepare transfer parameters */
	2593	hi2c->pBuffPtr = pData;
	2594	hi2c->XferCount = Size;
	2595	hi2c->XferOptions = XferOptions;
	2596	hi2c->XferISR = I2C_Master_ISR_IT;
	2597
	2598	/* If size > MAX_NBYTE_SIZE, use reload mode */
	2599	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2600	{
	2601	hi2c->XferSize = MAX_NBYTE_SIZE;
	2602	xfermode = I2C_RELOAD_MODE;
	2603	}
	2604	else
	2605	{
	2606	hi2c->XferSize = hi2c->XferCount;
	2607	xfermode = hi2c->XferOptions;
	2608	}
	2609
	2610	/* If transfer direction not change, do not generate Restart Condition */
	2611	/* Mean Previous state is same as current state */
	2612	if (hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX)
	2613	{
	2614	xferrequest = I2C_NO_STARTSTOP;
	2615	}
	2616
	2617	/* Send Slave Address and set NBYTES to write */
	2618	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, xferrequest);
	2619
	2620	/* Process Unlocked */
	2621	__HAL_UNLOCK(hi2c);
	2622
	2623	/* Note : The I2C interrupts must be enabled after unlocking current process
	2624	to avoid the risk of I2C interrupt handle execution before current
	2625	process unlock */
	2626	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
	2627
	2628	return HAL_OK;
	2629	}
	2630	else
	2631	{
	2632	return HAL_BUSY;
	2633	}
	2634	}
	2635
	2636	/**
	2637	* @brief Sequential receive in master I2C mode an amount of data in non-blocking mode with Interrupt
	2638	* @note This interface allow to manage repeated start condition when a direction change during transfer
	2639	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2640	* the configuration information for the specified I2C.
	2641	* @param DevAddress Target device address: The device 7 bits address value
	2642	* in datasheet must be shift at right before call interface
	2643	* @param pData Pointer to data buffer
	2644	* @param Size Amount of data to be sent
	2645	* @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS
	2646	* @retval HAL status
	2647	*/
	2648	HAL_StatusTypeDef HAL_I2C_Master_Sequential_Receive_IT(I2C_HandleTypeDef hi2c, uint16_t DevAddress, uint8_t pData, uint16_t Size, uint32_t XferOptions)
	2649	{
	2650	uint32_t xfermode = 0U;
	2651	uint32_t xferrequest = I2C_GENERATE_START_READ;
	2652
	2653	/* Check the parameters */
	2654	assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions));
	2655
	2656	if (hi2c->State == HAL_I2C_STATE_READY)
	2657	{
	2658	/* Process Locked */
	2659	__HAL_LOCK(hi2c);
	2660
	2661	hi2c->State = HAL_I2C_STATE_BUSY_RX;
	2662	hi2c->Mode = HAL_I2C_MODE_MASTER;
	2663	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2664
	2665	/* Prepare transfer parameters */
	2666	hi2c->pBuffPtr = pData;
	2667	hi2c->XferCount = Size;
	2668	hi2c->XferOptions = XferOptions;
	2669	hi2c->XferISR = I2C_Master_ISR_IT;
	2670
	2671	/* If hi2c->XferCount > MAX_NBYTE_SIZE, use reload mode */
	2672	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	2673	{
	2674	hi2c->XferSize = MAX_NBYTE_SIZE;
	2675	xfermode = I2C_RELOAD_MODE;
	2676	}
	2677	else
	2678	{
	2679	hi2c->XferSize = hi2c->XferCount;
	2680	xfermode = hi2c->XferOptions;
	2681	}
	2682
	2683	/* If transfer direction not change, do not generate Restart Condition */
	2684	/* Mean Previous state is same as current state */
	2685	if (hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX)
	2686	{
	2687	xferrequest = I2C_NO_STARTSTOP;
	2688	}
	2689
	2690	/* Send Slave Address and set NBYTES to read */
	2691	I2C_TransferConfig(hi2c, DevAddress, hi2c->XferSize, xfermode, xferrequest);
	2692
	2693	/* Process Unlocked */
	2694	__HAL_UNLOCK(hi2c);
	2695
	2696	/* Note : The I2C interrupts must be enabled after unlocking current process
	2697	to avoid the risk of I2C interrupt handle execution before current
	2698	process unlock */
	2699	I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT);
	2700
	2701	return HAL_OK;
	2702	}
	2703	else
	2704	{
	2705	return HAL_BUSY;
	2706	}
	2707	}
	2708
	2709	/**
	2710	* @brief Sequential transmit in slave/device I2C mode an amount of data in non-blocking mode with Interrupt
	2711	* @note This interface allow to manage repeated start condition when a direction change during transfer
	2712	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2713	* the configuration information for the specified I2C.
	2714	* @param pData Pointer to data buffer
	2715	* @param Size Amount of data to be sent
	2716	* @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS
	2717	* @retval HAL status
	2718	*/
	2719	HAL_StatusTypeDef HAL_I2C_Slave_Sequential_Transmit_IT(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size, uint32_t XferOptions)
	2720	{
	2721	/* Check the parameters */
	2722	assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions));
	2723
	2724	if ((hi2c->State & HAL_I2C_STATE_LISTEN) == HAL_I2C_STATE_LISTEN)
	2725	{
	2726	if ((pData == NULL) \|\| (Size == 0U))
	2727	{
	2728	return HAL_ERROR;
	2729	}
	2730
	2731	/* Disable Interrupts, to prevent preemption during treatment in case of multicall */
	2732	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT \| I2C_XFER_TX_IT);
	2733
	2734	/* Process Locked */
	2735	__HAL_LOCK(hi2c);
	2736
	2737	/* I2C cannot manage full duplex exchange so disable previous IT enabled if any */
	2738	/* and then toggle the HAL slave RX state to TX state */
	2739	if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN)
	2740	{
	2741	/* Disable associated Interrupts */
	2742	I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT);
	2743	}
	2744
	2745	hi2c->State = HAL_I2C_STATE_BUSY_TX_LISTEN;
	2746	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	2747	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2748
	2749	/* Enable Address Acknowledge */
	2750	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	2751
	2752	/* Prepare transfer parameters */
	2753	hi2c->pBuffPtr = pData;
	2754	hi2c->XferCount = Size;
	2755	hi2c->XferSize = hi2c->XferCount;
	2756	hi2c->XferOptions = XferOptions;
	2757	hi2c->XferISR = I2C_Slave_ISR_IT;
	2758
	2759	if (I2C_GET_DIR(hi2c) == I2C_DIRECTION_RECEIVE)
	2760	{
	2761	/* Clear ADDR flag after prepare the transfer parameters */
	2762	/* This action will generate an acknowledge to the Master */
	2763	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	2764	}
	2765
	2766	/* Process Unlocked */
	2767	__HAL_UNLOCK(hi2c);
	2768
	2769	/* Note : The I2C interrupts must be enabled after unlocking current process
	2770	to avoid the risk of I2C interrupt handle execution before current
	2771	process unlock */
	2772	/* REnable ADDR interrupt */
	2773	I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT \| I2C_XFER_LISTEN_IT);
	2774
	2775	return HAL_OK;
	2776	}
	2777	else
	2778	{
	2779	return HAL_ERROR;
	2780	}
	2781	}
	2782
	2783	/**
	2784	* @brief Sequential receive in slave/device I2C mode an amount of data in non-blocking mode with Interrupt
	2785	* @note This interface allow to manage repeated start condition when a direction change during transfer
	2786	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2787	* the configuration information for the specified I2C.
	2788	* @param pData Pointer to data buffer
	2789	* @param Size Amount of data to be sent
	2790	* @param XferOptions Options of Transfer, value of @ref I2C_XFEROPTIONS
	2791	* @retval HAL status
	2792	*/
	2793	HAL_StatusTypeDef HAL_I2C_Slave_Sequential_Receive_IT(I2C_HandleTypeDef hi2c, uint8_t pData, uint16_t Size, uint32_t XferOptions)
	2794	{
	2795	/* Check the parameters */
	2796	assert_param(IS_I2C_TRANSFER_OPTIONS_REQUEST(XferOptions));
	2797
	2798	if ((hi2c->State & HAL_I2C_STATE_LISTEN) == HAL_I2C_STATE_LISTEN)
	2799	{
	2800	if ((pData == NULL) \|\| (Size == 0U))
	2801	{
	2802	return HAL_ERROR;
	2803	}
	2804
	2805	/* Disable Interrupts, to prevent preemption during treatment in case of multicall */
	2806	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT \| I2C_XFER_RX_IT);
	2807
	2808	/* Process Locked */
	2809	__HAL_LOCK(hi2c);
	2810
	2811	/* I2C cannot manage full duplex exchange so disable previous IT enabled if any */
	2812	/* and then toggle the HAL slave TX state to RX state */
	2813	if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN)
	2814	{
	2815	/* Disable associated Interrupts */
	2816	I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT);
	2817	}
	2818
	2819	hi2c->State = HAL_I2C_STATE_BUSY_RX_LISTEN;
	2820	hi2c->Mode = HAL_I2C_MODE_SLAVE;
	2821	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	2822
	2823	/* Enable Address Acknowledge */
	2824	hi2c->Instance->CR2 &= ~I2C_CR2_NACK;
	2825
	2826	/* Prepare transfer parameters */
	2827	hi2c->pBuffPtr = pData;
	2828	hi2c->XferCount = Size;
	2829	hi2c->XferSize = hi2c->XferCount;
	2830	hi2c->XferOptions = XferOptions;
	2831	hi2c->XferISR = I2C_Slave_ISR_IT;
	2832
	2833	if (I2C_GET_DIR(hi2c) == I2C_DIRECTION_TRANSMIT)
	2834	{
	2835	/* Clear ADDR flag after prepare the transfer parameters */
	2836	/* This action will generate an acknowledge to the Master */
	2837	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	2838	}
	2839
	2840	/* Process Unlocked */
	2841	__HAL_UNLOCK(hi2c);
	2842
	2843	/* Note : The I2C interrupts must be enabled after unlocking current process
	2844	to avoid the risk of I2C interrupt handle execution before current
	2845	process unlock */
	2846	/* REnable ADDR interrupt */
	2847	I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT \| I2C_XFER_LISTEN_IT);
	2848
	2849	return HAL_OK;
	2850	}
	2851	else
	2852	{
	2853	return HAL_ERROR;
	2854	}
	2855	}
	2856
	2857	/**
	2858	* @brief Enable the Address listen mode with Interrupt.
	2859	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2860	* the configuration information for the specified I2C.
	2861	* @retval HAL status
	2862	*/
	2863	HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c)
	2864	{
	2865	if (hi2c->State == HAL_I2C_STATE_READY)
	2866	{
	2867	hi2c->State = HAL_I2C_STATE_LISTEN;
	2868	hi2c->XferISR = I2C_Slave_ISR_IT;
	2869
	2870	/* Enable the Address Match interrupt */
	2871	I2C_Enable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	2872
	2873	return HAL_OK;
	2874	}
	2875	else
	2876	{
	2877	return HAL_BUSY;
	2878	}
	2879	}
	2880
	2881	/**
	2882	* @brief Disable the Address listen mode with Interrupt.
	2883	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2884	* the configuration information for the specified I2C
	2885	* @retval HAL status
	2886	*/
	2887	HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c)
	2888	{
	2889	/* Declaration of tmp to prevent undefined behavior of volatile usage */
	2890	uint32_t tmp;
	2891
	2892	/* Disable Address listen mode only if a transfer is not ongoing */
	2893	if (hi2c->State == HAL_I2C_STATE_LISTEN)
	2894	{
	2895	tmp = (uint32_t)(hi2c->State) & I2C_STATE_MSK;
	2896	hi2c->PreviousState = tmp \| (uint32_t)(hi2c->Mode);
	2897	hi2c->State = HAL_I2C_STATE_READY;
	2898	hi2c->Mode = HAL_I2C_MODE_NONE;
	2899	hi2c->XferISR = NULL;
	2900
	2901	/* Disable the Address Match interrupt */
	2902	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	2903
	2904	return HAL_OK;
	2905	}
	2906	else
	2907	{
	2908	return HAL_BUSY;
	2909	}
	2910	}
	2911
	2912	/**
	2913	* @brief Abort a master I2C IT or DMA process communication with Interrupt.
	2914	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2915	* the configuration information for the specified I2C.
	2916	* @param DevAddress Target device address: The device 7 bits address value
	2917	* in datasheet must be shift at right before call interface
	2918	* @retval HAL status
	2919	*/
	2920	HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress)
	2921	{
	2922	if (hi2c->Mode == HAL_I2C_MODE_MASTER)
	2923	{
	2924	/* Process Locked */
	2925	__HAL_LOCK(hi2c);
	2926
	2927	/* Disable Interrupts */
	2928	I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT);
	2929	I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT);
	2930
	2931	/* Set State at HAL_I2C_STATE_ABORT */
	2932	hi2c->State = HAL_I2C_STATE_ABORT;
	2933
	2934	/* Set NBYTES to 1 to generate a dummy read on I2C peripheral */
	2935	/* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */
	2936	I2C_TransferConfig(hi2c, DevAddress, 1, I2C_AUTOEND_MODE, I2C_GENERATE_STOP);
	2937
	2938	/* Process Unlocked */
	2939	__HAL_UNLOCK(hi2c);
	2940
	2941	/* Note : The I2C interrupts must be enabled after unlocking current process
	2942	to avoid the risk of I2C interrupt handle execution before current
	2943	process unlock */
	2944	I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT);
	2945
	2946	return HAL_OK;
	2947	}
	2948	else
	2949	{
	2950	/* Wrong usage of abort function */
	2951	/* This function should be used only in case of abort monitored by master device */
	2952	return HAL_ERROR;
	2953	}
	2954	}
	2955
	2956	/**
	2957	* @}
	2958	*/
	2959
	2960	/** @defgroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
	2961	* @{
	2962	*/
	2963
	2964	/**
	2965	* @brief This function handles I2C event interrupt request.
	2966	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2967	* the configuration information for the specified I2C.
	2968	* @retval None
	2969	*/
	2970	void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c)
	2971	{
	2972	/* Get current IT Flags and IT sources value */
	2973	uint32_t itflags = READ_REG(hi2c->Instance->ISR);
	2974	uint32_t itsources = READ_REG(hi2c->Instance->CR1);
	2975
	2976	/* I2C events treatment -------------------------------------*/
	2977	if (hi2c->XferISR != NULL)
	2978	{
	2979	hi2c->XferISR(hi2c, itflags, itsources);
	2980	}
	2981	}
	2982
	2983	/**
	2984	* @brief This function handles I2C error interrupt request.
	2985	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	2986	* the configuration information for the specified I2C.
	2987	* @retval None
	2988	*/
	2989	void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c)
	2990	{
	2991	uint32_t itflags = READ_REG(hi2c->Instance->ISR);
	2992	uint32_t itsources = READ_REG(hi2c->Instance->CR1);
	2993
	2994	/* I2C Bus error interrupt occurred ------------------------------------*/
	2995	if (((itflags & I2C_FLAG_BERR) != RESET) && ((itsources & I2C_IT_ERRI) != RESET))
	2996	{
	2997	hi2c->ErrorCode \|= HAL_I2C_ERROR_BERR;
	2998
	2999	/* Clear BERR flag */
	3000	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_BERR);
	3001	}
	3002
	3003	/* I2C Over-Run/Under-Run interrupt occurred ----------------------------------------*/
	3004	if (((itflags & I2C_FLAG_OVR) != RESET) && ((itsources & I2C_IT_ERRI) != RESET))
	3005	{
	3006	hi2c->ErrorCode \|= HAL_I2C_ERROR_OVR;
	3007
	3008	/* Clear OVR flag */
	3009	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_OVR);
	3010	}
	3011
	3012	/* I2C Arbitration Loss error interrupt occurred -------------------------------------*/
	3013	if (((itflags & I2C_FLAG_ARLO) != RESET) && ((itsources & I2C_IT_ERRI) != RESET))
	3014	{
	3015	hi2c->ErrorCode \|= HAL_I2C_ERROR_ARLO;
	3016
	3017	/* Clear ARLO flag */
	3018	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ARLO);
	3019	}
	3020
	3021	/* Call the Error Callback in case of Error detected */
	3022	if ((hi2c->ErrorCode & (HAL_I2C_ERROR_BERR \| HAL_I2C_ERROR_OVR \| HAL_I2C_ERROR_ARLO)) != HAL_I2C_ERROR_NONE)
	3023	{
	3024	I2C_ITError(hi2c, hi2c->ErrorCode);
	3025	}
	3026	}
	3027
	3028	/**
	3029	* @brief Master Tx Transfer completed callback.
	3030	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3031	* the configuration information for the specified I2C.
	3032	* @retval None
	3033	*/
	3034	__weak void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c)
	3035	{
	3036	/* Prevent unused argument(s) compilation warning */
	3037	UNUSED(hi2c);
	3038
	3039	/* NOTE : This function should not be modified, when the callback is needed,
	3040	the HAL_I2C_MasterTxCpltCallback could be implemented in the user file
	3041	*/
	3042	}
	3043
	3044	/**
	3045	* @brief Master Rx Transfer completed callback.
	3046	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3047	* the configuration information for the specified I2C.
	3048	* @retval None
	3049	*/
	3050	__weak void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c)
	3051	{
	3052	/* Prevent unused argument(s) compilation warning */
	3053	UNUSED(hi2c);
	3054
	3055	/* NOTE : This function should not be modified, when the callback is needed,
	3056	the HAL_I2C_MasterRxCpltCallback could be implemented in the user file
	3057	*/
	3058	}
	3059
	3060	/** @brief Slave Tx Transfer completed callback.
	3061	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3062	* the configuration information for the specified I2C.
	3063	* @retval None
	3064	*/
	3065	__weak void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c)
	3066	{
	3067	/* Prevent unused argument(s) compilation warning */
	3068	UNUSED(hi2c);
	3069
	3070	/* NOTE : This function should not be modified, when the callback is needed,
	3071	the HAL_I2C_SlaveTxCpltCallback could be implemented in the user file
	3072	*/
	3073	}
	3074
	3075	/**
	3076	* @brief Slave Rx Transfer completed callback.
	3077	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3078	* the configuration information for the specified I2C.
	3079	* @retval None
	3080	*/
	3081	__weak void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c)
	3082	{
	3083	/* Prevent unused argument(s) compilation warning */
	3084	UNUSED(hi2c);
	3085
	3086	/* NOTE : This function should not be modified, when the callback is needed,
	3087	the HAL_I2C_SlaveRxCpltCallback could be implemented in the user file
	3088	*/
	3089	}
	3090
	3091	/**
	3092	* @brief Slave Address Match callback.
	3093	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3094	* the configuration information for the specified I2C.
	3095	* @param TransferDirection Master request Transfer Direction (Write/Read), value of @ref I2C_XFERDIRECTION
	3096	* @param AddrMatchCode Address Match Code
	3097	* @retval None
	3098	*/
	3099	__weak void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode)
	3100	{
	3101	/* Prevent unused argument(s) compilation warning */
	3102	UNUSED(hi2c);
	3103	UNUSED(TransferDirection);
	3104	UNUSED(AddrMatchCode);
	3105
	3106	/* NOTE : This function should not be modified, when the callback is needed,
	3107	the HAL_I2C_AddrCallback() could be implemented in the user file
	3108	*/
	3109	}
	3110
	3111	/**
	3112	* @brief Listen Complete callback.
	3113	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3114	* the configuration information for the specified I2C.
	3115	* @retval None
	3116	*/
	3117	__weak void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c)
	3118	{
	3119	/* Prevent unused argument(s) compilation warning */
	3120	UNUSED(hi2c);
	3121
	3122	/* NOTE : This function should not be modified, when the callback is needed,
	3123	the HAL_I2C_ListenCpltCallback() could be implemented in the user file
	3124	*/
	3125	}
	3126
	3127	/**
	3128	* @brief Memory Tx Transfer completed callback.
	3129	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3130	* the configuration information for the specified I2C.
	3131	* @retval None
	3132	*/
	3133	__weak void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c)
	3134	{
	3135	/* Prevent unused argument(s) compilation warning */
	3136	UNUSED(hi2c);
	3137
	3138	/* NOTE : This function should not be modified, when the callback is needed,
	3139	the HAL_I2C_MemTxCpltCallback could be implemented in the user file
	3140	*/
	3141	}
	3142
	3143	/**
	3144	* @brief Memory Rx Transfer completed callback.
	3145	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3146	* the configuration information for the specified I2C.
	3147	* @retval None
	3148	*/
	3149	__weak void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c)
	3150	{
	3151	/* Prevent unused argument(s) compilation warning */
	3152	UNUSED(hi2c);
	3153
	3154	/* NOTE : This function should not be modified, when the callback is needed,
	3155	the HAL_I2C_MemRxCpltCallback could be implemented in the user file
	3156	*/
	3157	}
	3158
	3159	/**
	3160	* @brief I2C error callback.
	3161	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3162	* the configuration information for the specified I2C.
	3163	* @retval None
	3164	*/
	3165	__weak void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c)
	3166	{
	3167	/* Prevent unused argument(s) compilation warning */
	3168	UNUSED(hi2c);
	3169
	3170	/* NOTE : This function should not be modified, when the callback is needed,
	3171	the HAL_I2C_ErrorCallback could be implemented in the user file
	3172	*/
	3173	}
	3174
	3175	/**
	3176	* @brief I2C abort callback.
	3177	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3178	* the configuration information for the specified I2C.
	3179	* @retval None
	3180	*/
	3181	__weak void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c)
	3182	{
	3183	/* Prevent unused argument(s) compilation warning */
	3184	UNUSED(hi2c);
	3185
	3186	/* NOTE : This function should not be modified, when the callback is needed,
	3187	the HAL_I2C_AbortCpltCallback could be implemented in the user file
	3188	*/
	3189	}
	3190
	3191	/**
	3192	* @}
	3193	*/
	3194
	3195	/** @defgroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions
	3196	* @brief Peripheral State, Mode and Error functions
	3197	*
	3198	@verbatim
	3199	===============================================================================
	3200	##### Peripheral State, Mode and Error functions #####
	3201	===============================================================================
	3202	[..]
	3203	This subsection permit to get in run-time the status of the peripheral
	3204	and the data flow.
	3205
	3206	@endverbatim
	3207	* @{
	3208	*/
	3209
	3210	/**
	3211	* @brief Return the I2C handle state.
	3212	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3213	* the configuration information for the specified I2C.
	3214	* @retval HAL state
	3215	*/
	3216	HAL_I2C_StateTypeDef HAL_I2C_GetState(I2C_HandleTypeDef *hi2c)
	3217	{
	3218	/* Return I2C handle state */
	3219	return hi2c->State;
	3220	}
	3221
	3222	/**
	3223	* @brief Returns the I2C Master, Slave, Memory or no mode.
	3224	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3225	* the configuration information for I2C module
	3226	* @retval HAL mode
	3227	*/
	3228	HAL_I2C_ModeTypeDef HAL_I2C_GetMode(I2C_HandleTypeDef *hi2c)
	3229	{
	3230	return hi2c->Mode;
	3231	}
	3232
	3233	/**
	3234	* @brief Return the I2C error code.
	3235	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3236	* the configuration information for the specified I2C.
	3237	* @retval I2C Error Code
	3238	*/
	3239	uint32_t HAL_I2C_GetError(I2C_HandleTypeDef *hi2c)
	3240	{
	3241	return hi2c->ErrorCode;
	3242	}
	3243
	3244	/**
	3245	* @}
	3246	*/
	3247
	3248	/**
	3249	* @}
	3250	*/
	3251
	3252	/** @addtogroup I2C_Private_Functions
	3253	* @{
	3254	*/
	3255
	3256	/**
	3257	* @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with Interrupt.
	3258	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3259	* the configuration information for the specified I2C.
	3260	* @param ITFlags Interrupt flags to handle.
	3261	* @param ITSources Interrupt sources enabled.
	3262	* @retval HAL status
	3263	*/
	3264	static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
	3265	{
	3266	uint16_t devaddress = 0U;
	3267
	3268	/* Process Locked */
	3269	__HAL_LOCK(hi2c);
	3270
	3271	if (((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET))
	3272	{
	3273	/* Clear NACK Flag */
	3274	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3275
	3276	/* Set corresponding Error Code */
	3277	/* No need to generate STOP, it is automatically done */
	3278	/* Error callback will be send during stop flag treatment */
	3279	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	3280
	3281	/* Flush TX register */
	3282	I2C_Flush_TXDR(hi2c);
	3283	}
	3284	else if (((ITFlags & I2C_FLAG_RXNE) != RESET) && ((ITSources & I2C_IT_RXI) != RESET))
	3285	{
	3286	/* Read data from RXDR */
	3287	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	3288	hi2c->XferSize--;
	3289	hi2c->XferCount--;
	3290	}
	3291	else if (((ITFlags & I2C_FLAG_TXIS) != RESET) && ((ITSources & I2C_IT_TXI) != RESET))
	3292	{
	3293	/* Write data to TXDR */
	3294	hi2c->Instance->TXDR = (*hi2c->pBuffPtr++);
	3295	hi2c->XferSize--;
	3296	hi2c->XferCount--;
	3297	}
	3298	else if (((ITFlags & I2C_FLAG_TCR) != RESET) && ((ITSources & I2C_IT_TCI) != RESET))
	3299	{
	3300	if ((hi2c->XferSize == 0U) && (hi2c->XferCount != 0U))
	3301	{
	3302	devaddress = (hi2c->Instance->CR2 & I2C_CR2_SADD);
	3303
	3304	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	3305	{
	3306	hi2c->XferSize = MAX_NBYTE_SIZE;
	3307	I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
	3308	}
	3309	else
	3310	{
	3311	hi2c->XferSize = hi2c->XferCount;
	3312	if (hi2c->XferOptions != I2C_NO_OPTION_FRAME)
	3313	{
	3314	I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, hi2c->XferOptions, I2C_NO_STARTSTOP);
	3315	}
	3316	else
	3317	{
	3318	I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
	3319	}
	3320	}
	3321	}
	3322	else
	3323	{
	3324	/* Call TxCpltCallback() if no stop mode is set */
	3325	if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE)
	3326	{
	3327	/* Call I2C Master Sequential complete process */
	3328	I2C_ITMasterSequentialCplt(hi2c);
	3329	}
	3330	else
	3331	{
	3332	/* Wrong size Status regarding TCR flag event */
	3333	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3334	I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE);
	3335	}
	3336	}
	3337	}
	3338	else if (((ITFlags & I2C_FLAG_TC) != RESET) && ((ITSources & I2C_IT_TCI) != RESET))
	3339	{
	3340	if (hi2c->XferCount == 0U)
	3341	{
	3342	if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE)
	3343	{
	3344	/* Generate a stop condition in case of no transfer option */
	3345	if (hi2c->XferOptions == I2C_NO_OPTION_FRAME)
	3346	{
	3347	/* Generate Stop */
	3348	hi2c->Instance->CR2 \|= I2C_CR2_STOP;
	3349	}
	3350	else
	3351	{
	3352	/* Call I2C Master Sequential complete process */
	3353	I2C_ITMasterSequentialCplt(hi2c);
	3354	}
	3355	}
	3356	}
	3357	else
	3358	{
	3359	/* Wrong size Status regarding TC flag event */
	3360	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3361	I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE);
	3362	}
	3363	}
	3364
	3365	if (((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET))
	3366	{
	3367	/* Call I2C Master complete process */
	3368	I2C_ITMasterCplt(hi2c, ITFlags);
	3369	}
	3370
	3371	/* Process Unlocked */
	3372	__HAL_UNLOCK(hi2c);
	3373
	3374	return HAL_OK;
	3375	}
	3376
	3377	/**
	3378	* @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with Interrupt.
	3379	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3380	* the configuration information for the specified I2C.
	3381	* @param ITFlags Interrupt flags to handle.
	3382	* @param ITSources Interrupt sources enabled.
	3383	* @retval HAL status
	3384	*/
	3385	static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
	3386	{
	3387	/* Process locked */
	3388	__HAL_LOCK(hi2c);
	3389
	3390	if (((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET))
	3391	{
	3392	/* Check that I2C transfer finished */
	3393	/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */
	3394	/* Mean XferCount == 0*/
	3395	/* So clear Flag NACKF only */
	3396	if (hi2c->XferCount == 0U)
	3397	{
	3398	if (((hi2c->XferOptions == I2C_FIRST_AND_LAST_FRAME) \|\| (hi2c->XferOptions == I2C_LAST_FRAME)) && \
	3399	(hi2c->State == HAL_I2C_STATE_LISTEN))
	3400	{
	3401	/* Call I2C Listen complete process */
	3402	I2C_ITListenCplt(hi2c, ITFlags);
	3403	}
	3404	else if ((hi2c->XferOptions != I2C_NO_OPTION_FRAME) && (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN))
	3405	{
	3406	/* Clear NACK Flag */
	3407	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3408
	3409	/* Flush TX register */
	3410	I2C_Flush_TXDR(hi2c);
	3411
	3412	/* Last Byte is Transmitted */
	3413	/* Call I2C Slave Sequential complete process */
	3414	I2C_ITSlaveSequentialCplt(hi2c);
	3415	}
	3416	else
	3417	{
	3418	/* Clear NACK Flag */
	3419	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3420	}
	3421	}
	3422	else
	3423	{
	3424	/* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/
	3425	/* Clear NACK Flag */
	3426	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3427
	3428	/* Set ErrorCode corresponding to a Non-Acknowledge */
	3429	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	3430	}
	3431	}
	3432	else if (((ITFlags & I2C_FLAG_RXNE) != RESET) && ((ITSources & I2C_IT_RXI) != RESET))
	3433	{
	3434	if (hi2c->XferCount > 0U)
	3435	{
	3436	/* Read data from RXDR */
	3437	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	3438	hi2c->XferSize--;
	3439	hi2c->XferCount--;
	3440	}
	3441
	3442	if ((hi2c->XferCount == 0U) && \
	3443	(hi2c->XferOptions != I2C_NO_OPTION_FRAME))
	3444	{
	3445	/* Call I2C Slave Sequential complete process */
	3446	I2C_ITSlaveSequentialCplt(hi2c);
	3447	}
	3448	}
	3449	else if (((ITFlags & I2C_FLAG_ADDR) != RESET) && ((ITSources & I2C_IT_ADDRI) != RESET))
	3450	{
	3451	I2C_ITAddrCplt(hi2c, ITFlags);
	3452	}
	3453	else if (((ITFlags & I2C_FLAG_TXIS) != RESET) && ((ITSources & I2C_IT_TXI) != RESET))
	3454	{
	3455	/* Write data to TXDR only if XferCount not reach "0" */
	3456	/* A TXIS flag can be set, during STOP treatment */
	3457	/* Check if all Datas have already been sent */
	3458	/* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */
	3459	if (hi2c->XferCount > 0U)
	3460	{
	3461	/* Write data to TXDR */
	3462	hi2c->Instance->TXDR = (*hi2c->pBuffPtr++);
	3463	hi2c->XferCount--;
	3464	hi2c->XferSize--;
	3465	}
	3466	else
	3467	{
	3468	if ((hi2c->XferOptions == I2C_NEXT_FRAME) \|\| (hi2c->XferOptions == I2C_FIRST_FRAME))
	3469	{
	3470	/* Last Byte is Transmitted */
	3471	/* Call I2C Slave Sequential complete process */
	3472	I2C_ITSlaveSequentialCplt(hi2c);
	3473	}
	3474	}
	3475	}
	3476
	3477	/* Check if STOPF is set */
	3478	if (((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET))
	3479	{
	3480	/* Call I2C Slave complete process */
	3481	I2C_ITSlaveCplt(hi2c, ITFlags);
	3482	}
	3483
	3484	/* Process Unlocked */
	3485	__HAL_UNLOCK(hi2c);
	3486
	3487	return HAL_OK;
	3488	}
	3489
	3490	/**
	3491	* @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode with DMA.
	3492	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3493	* the configuration information for the specified I2C.
	3494	* @param ITFlags Interrupt flags to handle.
	3495	* @param ITSources Interrupt sources enabled.
	3496	* @retval HAL status
	3497	*/
	3498	static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
	3499	{
	3500	uint16_t devaddress = 0U;
	3501	uint32_t xfermode = 0U;
	3502
	3503	/* Process Locked */
	3504	__HAL_LOCK(hi2c);
	3505
	3506	if (((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET))
	3507	{
	3508	/* Clear NACK Flag */
	3509	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3510
	3511	/* Set corresponding Error Code */
	3512	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	3513
	3514	/* No need to generate STOP, it is automatically done */
	3515	/* But enable STOP interrupt, to treat it */
	3516	/* Error callback will be send during stop flag treatment */
	3517	I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT);
	3518
	3519	/* Flush TX register */
	3520	I2C_Flush_TXDR(hi2c);
	3521	}
	3522	else if (((ITFlags & I2C_FLAG_TCR) != RESET) && ((ITSources & I2C_IT_TCI) != RESET))
	3523	{
	3524	/* Disable TC interrupt */
	3525	__HAL_I2C_DISABLE_IT(hi2c, I2C_IT_TCI);
	3526
	3527	if (hi2c->XferCount != 0U)
	3528	{
	3529	/* Recover Slave address */
	3530	devaddress = (hi2c->Instance->CR2 & I2C_CR2_SADD);
	3531
	3532	/* Prepare the new XferSize to transfer */
	3533	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	3534	{
	3535	hi2c->XferSize = MAX_NBYTE_SIZE;
	3536	xfermode = I2C_RELOAD_MODE;
	3537	}
	3538	else
	3539	{
	3540	hi2c->XferSize = hi2c->XferCount;
	3541	xfermode = I2C_AUTOEND_MODE;
	3542	}
	3543
	3544	/* Set the new XferSize in Nbytes register */
	3545	I2C_TransferConfig(hi2c, devaddress, hi2c->XferSize, xfermode, I2C_NO_STARTSTOP);
	3546
	3547	/* Update XferCount value */
	3548	hi2c->XferCount -= hi2c->XferSize;
	3549
	3550	/* Enable DMA Request */
	3551	if (hi2c->State == HAL_I2C_STATE_BUSY_RX)
	3552	{
	3553	hi2c->Instance->CR1 \|= I2C_CR1_RXDMAEN;
	3554	}
	3555	else
	3556	{
	3557	hi2c->Instance->CR1 \|= I2C_CR1_TXDMAEN;
	3558	}
	3559	}
	3560	else
	3561	{
	3562	/* Wrong size Status regarding TCR flag event */
	3563	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3564	I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE);
	3565	}
	3566	}
	3567	else if (((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET))
	3568	{
	3569	/* Call I2C Master complete process */
	3570	I2C_ITMasterCplt(hi2c, ITFlags);
	3571	}
	3572
	3573	/* Process Unlocked */
	3574	__HAL_UNLOCK(hi2c);
	3575
	3576	return HAL_OK;
	3577	}
	3578
	3579	/**
	3580	* @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode with DMA.
	3581	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3582	* the configuration information for the specified I2C.
	3583	* @param ITFlags Interrupt flags to handle.
	3584	* @param ITSources Interrupt sources enabled.
	3585	* @retval HAL status
	3586	*/
	3587	static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
	3588	{
	3589	/* Process locked */
	3590	__HAL_LOCK(hi2c);
	3591
	3592	if (((ITFlags & I2C_FLAG_AF) != RESET) && ((ITSources & I2C_IT_NACKI) != RESET))
	3593	{
	3594	/* Check that I2C transfer finished */
	3595	/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */
	3596	/* Mean XferCount == 0 */
	3597	/* So clear Flag NACKF only */
	3598	if (I2C_GET_DMA_REMAIN_DATA(hi2c) == 0U)
	3599	{
	3600	/* Clear NACK Flag */
	3601	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3602	}
	3603	else
	3604	{
	3605	/* if no, error use case, a Non-Acknowledge of last Data is generated by the MASTER*/
	3606	/* Clear NACK Flag */
	3607	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3608
	3609	/* Set ErrorCode corresponding to a Non-Acknowledge */
	3610	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	3611	}
	3612	}
	3613	else if (((ITFlags & I2C_FLAG_ADDR) != RESET) && ((ITSources & I2C_IT_ADDRI) != RESET))
	3614	{
	3615	/* Clear ADDR flag */
	3616	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	3617	}
	3618	else if (((ITFlags & I2C_FLAG_STOPF) != RESET) && ((ITSources & I2C_IT_STOPI) != RESET))
	3619	{
	3620	/* Call I2C Slave complete process */
	3621	I2C_ITSlaveCplt(hi2c, ITFlags);
	3622	}
	3623
	3624	/* Process Unlocked */
	3625	__HAL_UNLOCK(hi2c);
	3626
	3627	return HAL_OK;
	3628	}
	3629
	3630	/**
	3631	* @brief Master sends target device address followed by internal memory address for write request.
	3632	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3633	* the configuration information for the specified I2C.
	3634	* @param DevAddress Target device address: The device 7 bits address value
	3635	* in datasheet must be shift at right before call interface
	3636	* @param MemAddress Internal memory address
	3637	* @param MemAddSize Size of internal memory address
	3638	* @param Timeout Timeout duration
	3639	* @param Tickstart Tick start value
	3640	* @retval HAL status
	3641	*/
	3642	static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart)
	3643	{
	3644	I2C_TransferConfig(hi2c, DevAddress, MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE);
	3645
	3646	/* Wait until TXIS flag is set */
	3647	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK)
	3648	{
	3649	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	3650	{
	3651	return HAL_ERROR;
	3652	}
	3653	else
	3654	{
	3655	return HAL_TIMEOUT;
	3656	}
	3657	}
	3658
	3659	/* If Memory address size is 8Bit */
	3660	if (MemAddSize == I2C_MEMADD_SIZE_8BIT)
	3661	{
	3662	/* Send Memory Address */
	3663	hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress);
	3664	}
	3665	/* If Memory address size is 16Bit */
	3666	else
	3667	{
	3668	/* Send MSB of Memory Address */
	3669	hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress);
	3670
	3671	/* Wait until TXIS flag is set */
	3672	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK)
	3673	{
	3674	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	3675	{
	3676	return HAL_ERROR;
	3677	}
	3678	else
	3679	{
	3680	return HAL_TIMEOUT;
	3681	}
	3682	}
	3683
	3684	/* Send LSB of Memory Address */
	3685	hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress);
	3686	}
	3687
	3688	/* Wait until TCR flag is set */
	3689	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TCR, RESET, Timeout, Tickstart) != HAL_OK)
	3690	{
	3691	return HAL_TIMEOUT;
	3692	}
	3693
	3694	return HAL_OK;
	3695	}
	3696
	3697	/**
	3698	* @brief Master sends target device address followed by internal memory address for read request.
	3699	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	3700	* the configuration information for the specified I2C.
	3701	* @param DevAddress Target device address: The device 7 bits address value
	3702	* in datasheet must be shift at right before call interface
	3703	* @param MemAddress Internal memory address
	3704	* @param MemAddSize Size of internal memory address
	3705	* @param Timeout Timeout duration
	3706	* @param Tickstart Tick start value
	3707	* @retval HAL status
	3708	*/
	3709	static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart)
	3710	{
	3711	I2C_TransferConfig(hi2c, DevAddress, MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE);
	3712
	3713	/* Wait until TXIS flag is set */
	3714	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK)
	3715	{
	3716	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	3717	{
	3718	return HAL_ERROR;
	3719	}
	3720	else
	3721	{
	3722	return HAL_TIMEOUT;
	3723	}
	3724	}
	3725
	3726	/* If Memory address size is 8Bit */
	3727	if (MemAddSize == I2C_MEMADD_SIZE_8BIT)
	3728	{
	3729	/* Send Memory Address */
	3730	hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress);
	3731	}
	3732	/* If Memory address size is 16Bit */
	3733	else
	3734	{
	3735	/* Send MSB of Memory Address */
	3736	hi2c->Instance->TXDR = I2C_MEM_ADD_MSB(MemAddress);
	3737
	3738	/* Wait until TXIS flag is set */
	3739	if (I2C_WaitOnTXISFlagUntilTimeout(hi2c, Timeout, Tickstart) != HAL_OK)
	3740	{
	3741	if (hi2c->ErrorCode == HAL_I2C_ERROR_AF)
	3742	{
	3743	return HAL_ERROR;
	3744	}
	3745	else
	3746	{
	3747	return HAL_TIMEOUT;
	3748	}
	3749	}
	3750
	3751	/* Send LSB of Memory Address */
	3752	hi2c->Instance->TXDR = I2C_MEM_ADD_LSB(MemAddress);
	3753	}
	3754
	3755	/* Wait until TC flag is set */
	3756	if (I2C_WaitOnFlagUntilTimeout(hi2c, I2C_FLAG_TC, RESET, Timeout, Tickstart) != HAL_OK)
	3757	{
	3758	return HAL_TIMEOUT;
	3759	}
	3760
	3761	return HAL_OK;
	3762	}
	3763
	3764	/**
	3765	* @brief I2C Address complete process callback.
	3766	* @param hi2c I2C handle.
	3767	* @param ITFlags Interrupt flags to handle.
	3768	* @retval None
	3769	*/
	3770	static void I2C_ITAddrCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags)
	3771	{
	3772	uint8_t transferdirection = 0U;
	3773	uint16_t slaveaddrcode = 0U;
	3774	uint16_t ownadd1code = 0U;
	3775	uint16_t ownadd2code = 0U;
	3776
	3777	/* Prevent unused argument(s) compilation warning */
	3778	UNUSED(ITFlags);
	3779
	3780	/* In case of Listen state, need to inform upper layer of address match code event */
	3781	if ((hi2c->State & HAL_I2C_STATE_LISTEN) == HAL_I2C_STATE_LISTEN)
	3782	{
	3783	transferdirection = I2C_GET_DIR(hi2c);
	3784	slaveaddrcode = I2C_GET_ADDR_MATCH(hi2c);
	3785	ownadd1code = I2C_GET_OWN_ADDRESS1(hi2c);
	3786	ownadd2code = I2C_GET_OWN_ADDRESS2(hi2c);
	3787
	3788	/* If 10bits addressing mode is selected */
	3789	if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT)
	3790	{
	3791	if ((slaveaddrcode & SlaveAddr_MSK) == ((ownadd1code >> SlaveAddr_SHIFT) & SlaveAddr_MSK))
	3792	{
	3793	slaveaddrcode = ownadd1code;
	3794	hi2c->AddrEventCount++;
	3795	if (hi2c->AddrEventCount == 2U)
	3796	{
	3797	/* Reset Address Event counter */
	3798	hi2c->AddrEventCount = 0U;
	3799
	3800	/* Clear ADDR flag */
	3801	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	3802
	3803	/* Process Unlocked */
	3804	__HAL_UNLOCK(hi2c);
	3805
	3806	/* Call Slave Addr callback */
	3807	HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode);
	3808	}
	3809	}
	3810	else
	3811	{
	3812	slaveaddrcode = ownadd2code;
	3813
	3814	/* Disable ADDR Interrupts */
	3815	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	3816
	3817	/* Process Unlocked */
	3818	__HAL_UNLOCK(hi2c);
	3819
	3820	/* Call Slave Addr callback */
	3821	HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode);
	3822	}
	3823	}
	3824	/* else 7 bits addressing mode is selected */
	3825	else
	3826	{
	3827	/* Disable ADDR Interrupts */
	3828	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT);
	3829
	3830	/* Process Unlocked */
	3831	__HAL_UNLOCK(hi2c);
	3832
	3833	/* Call Slave Addr callback */
	3834	HAL_I2C_AddrCallback(hi2c, transferdirection, slaveaddrcode);
	3835	}
	3836	}
	3837	/* Else clear address flag only */
	3838	else
	3839	{
	3840	/* Clear ADDR flag */
	3841	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	3842
	3843	/* Process Unlocked */
	3844	__HAL_UNLOCK(hi2c);
	3845	}
	3846	}
	3847
	3848	/**
	3849	* @brief I2C Master sequential complete process.
	3850	* @param hi2c I2C handle.
	3851	* @retval None
	3852	*/
	3853	static void I2C_ITMasterSequentialCplt(I2C_HandleTypeDef *hi2c)
	3854	{
	3855	/* Reset I2C handle mode */
	3856	hi2c->Mode = HAL_I2C_MODE_NONE;
	3857
	3858	/* No Generate Stop, to permit restart mode */
	3859	/* The stop will be done at the end of transfer, when I2C_AUTOEND_MODE enable */
	3860	if (hi2c->State == HAL_I2C_STATE_BUSY_TX)
	3861	{
	3862	hi2c->State = HAL_I2C_STATE_READY;
	3863	hi2c->PreviousState = I2C_STATE_MASTER_BUSY_TX;
	3864	hi2c->XferISR = NULL;
	3865
	3866	/* Disable Interrupts */
	3867	I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT);
	3868
	3869	/* Process Unlocked */
	3870	__HAL_UNLOCK(hi2c);
	3871
	3872	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3873	HAL_I2C_MasterTxCpltCallback(hi2c);
	3874	}
	3875	/* hi2c->State == HAL_I2C_STATE_BUSY_RX */
	3876	else
	3877	{
	3878	hi2c->State = HAL_I2C_STATE_READY;
	3879	hi2c->PreviousState = I2C_STATE_MASTER_BUSY_RX;
	3880	hi2c->XferISR = NULL;
	3881
	3882	/* Disable Interrupts */
	3883	I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT);
	3884
	3885	/* Process Unlocked */
	3886	__HAL_UNLOCK(hi2c);
	3887
	3888	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3889	HAL_I2C_MasterRxCpltCallback(hi2c);
	3890	}
	3891	}
	3892
	3893	/**
	3894	* @brief I2C Slave sequential complete process.
	3895	* @param hi2c I2C handle.
	3896	* @retval None
	3897	*/
	3898	static void I2C_ITSlaveSequentialCplt(I2C_HandleTypeDef *hi2c)
	3899	{
	3900	/* Reset I2C handle mode */
	3901	hi2c->Mode = HAL_I2C_MODE_NONE;
	3902
	3903	if (hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN)
	3904	{
	3905	/* Remove HAL_I2C_STATE_SLAVE_BUSY_TX, keep only HAL_I2C_STATE_LISTEN */
	3906	hi2c->State = HAL_I2C_STATE_LISTEN;
	3907	hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_TX;
	3908
	3909	/* Disable Interrupts */
	3910	I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT);
	3911
	3912	/* Process Unlocked */
	3913	__HAL_UNLOCK(hi2c);
	3914
	3915	/* Call the Tx complete callback to inform upper layer of the end of transmit process */
	3916	HAL_I2C_SlaveTxCpltCallback(hi2c);
	3917	}
	3918
	3919	else if (hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN)
	3920	{
	3921	/* Remove HAL_I2C_STATE_SLAVE_BUSY_RX, keep only HAL_I2C_STATE_LISTEN */
	3922	hi2c->State = HAL_I2C_STATE_LISTEN;
	3923	hi2c->PreviousState = I2C_STATE_SLAVE_BUSY_RX;
	3924
	3925	/* Disable Interrupts */
	3926	I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT);
	3927
	3928	/* Process Unlocked */
	3929	__HAL_UNLOCK(hi2c);
	3930
	3931	/* Call the Rx complete callback to inform upper layer of the end of receive process */
	3932	HAL_I2C_SlaveRxCpltCallback(hi2c);
	3933	}
	3934	}
	3935
	3936	/**
	3937	* @brief I2C Master complete process.
	3938	* @param hi2c I2C handle.
	3939	* @param ITFlags Interrupt flags to handle.
	3940	* @retval None
	3941	*/
	3942	static void I2C_ITMasterCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags)
	3943	{
	3944	/* Clear STOP Flag */
	3945	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	3946
	3947	/* Clear Configuration Register 2 */
	3948	I2C_RESET_CR2(hi2c);
	3949
	3950	/* Reset handle parameters */
	3951	hi2c->PreviousState = I2C_STATE_NONE;
	3952	hi2c->XferISR = NULL;
	3953	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	3954
	3955	if ((ITFlags & I2C_FLAG_AF) != RESET)
	3956	{
	3957	/* Clear NACK Flag */
	3958	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	3959
	3960	/* Set acknowledge error code */
	3961	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	3962	}
	3963
	3964	/* Flush TX register */
	3965	I2C_Flush_TXDR(hi2c);
	3966
	3967	/* Disable Interrupts */
	3968	I2C_Disable_IRQ(hi2c, I2C_XFER_TX_IT \| I2C_XFER_RX_IT);
	3969
	3970	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3971	if ((hi2c->ErrorCode != HAL_I2C_ERROR_NONE) \|\| (hi2c->State == HAL_I2C_STATE_ABORT))
	3972	{
	3973	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3974	I2C_ITError(hi2c, hi2c->ErrorCode);
	3975	}
	3976	/* hi2c->State == HAL_I2C_STATE_BUSY_TX */
	3977	else if (hi2c->State == HAL_I2C_STATE_BUSY_TX)
	3978	{
	3979	hi2c->State = HAL_I2C_STATE_READY;
	3980
	3981	if (hi2c->Mode == HAL_I2C_MODE_MEM)
	3982	{
	3983	hi2c->Mode = HAL_I2C_MODE_NONE;
	3984
	3985	/* Process Unlocked */
	3986	__HAL_UNLOCK(hi2c);
	3987
	3988	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3989	HAL_I2C_MemTxCpltCallback(hi2c);
	3990	}
	3991	else
	3992	{
	3993	hi2c->Mode = HAL_I2C_MODE_NONE;
	3994
	3995	/* Process Unlocked */
	3996	__HAL_UNLOCK(hi2c);
	3997
	3998	/* Call the corresponding callback to inform upper layer of End of Transfer */
	3999	HAL_I2C_MasterTxCpltCallback(hi2c);
	4000	}
	4001	}
	4002	/* hi2c->State == HAL_I2C_STATE_BUSY_RX */
	4003	else if (hi2c->State == HAL_I2C_STATE_BUSY_RX)
	4004	{
	4005	hi2c->State = HAL_I2C_STATE_READY;
	4006
	4007	if (hi2c->Mode == HAL_I2C_MODE_MEM)
	4008	{
	4009	hi2c->Mode = HAL_I2C_MODE_NONE;
	4010
	4011	/* Process Unlocked */
	4012	__HAL_UNLOCK(hi2c);
	4013
	4014	HAL_I2C_MemRxCpltCallback(hi2c);
	4015	}
	4016	else
	4017	{
	4018	hi2c->Mode = HAL_I2C_MODE_NONE;
	4019
	4020	/* Process Unlocked */
	4021	__HAL_UNLOCK(hi2c);
	4022
	4023	HAL_I2C_MasterRxCpltCallback(hi2c);
	4024	}
	4025	}
	4026	}
	4027
	4028	/**
	4029	* @brief I2C Slave complete process.
	4030	* @param hi2c I2C handle.
	4031	* @param ITFlags Interrupt flags to handle.
	4032	* @retval None
	4033	*/
	4034	static void I2C_ITSlaveCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags)
	4035	{
	4036	/* Clear STOP Flag */
	4037	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	4038
	4039	/* Clear ADDR flag */
	4040	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_ADDR);
	4041
	4042	/* Disable all interrupts */
	4043	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT \| I2C_XFER_TX_IT \| I2C_XFER_RX_IT);
	4044
	4045	/* Disable Address Acknowledge */
	4046	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	4047
	4048	/* Clear Configuration Register 2 */
	4049	I2C_RESET_CR2(hi2c);
	4050
	4051	/* Flush TX register */
	4052	I2C_Flush_TXDR(hi2c);
	4053
	4054	/* If a DMA is ongoing, Update handle size context */
	4055	if (((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN) \|\|
	4056	((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN))
	4057	{
	4058	hi2c->XferCount = I2C_GET_DMA_REMAIN_DATA(hi2c);
	4059	}
	4060
	4061	/* All data are not transferred, so set error code accordingly */
	4062	if (hi2c->XferCount != 0U)
	4063	{
	4064	/* Set ErrorCode corresponding to a Non-Acknowledge */
	4065	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	4066	}
	4067
	4068	/* Store Last receive data if any */
	4069	if (((ITFlags & I2C_FLAG_RXNE) != RESET))
	4070	{
	4071	/* Read data from RXDR */
	4072	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	4073
	4074	if ((hi2c->XferSize > 0U))
	4075	{
	4076	hi2c->XferSize--;
	4077	hi2c->XferCount--;
	4078
	4079	/* Set ErrorCode corresponding to a Non-Acknowledge */
	4080	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	4081	}
	4082	}
	4083
	4084	hi2c->PreviousState = I2C_STATE_NONE;
	4085	hi2c->Mode = HAL_I2C_MODE_NONE;
	4086	hi2c->XferISR = NULL;
	4087
	4088	if (hi2c->ErrorCode != HAL_I2C_ERROR_NONE)
	4089	{
	4090	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4091	I2C_ITError(hi2c, hi2c->ErrorCode);
	4092
	4093	/* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */
	4094	if (hi2c->State == HAL_I2C_STATE_LISTEN)
	4095	{
	4096	/* Call I2C Listen complete process */
	4097	I2C_ITListenCplt(hi2c, ITFlags);
	4098	}
	4099	}
	4100	else if (hi2c->XferOptions != I2C_NO_OPTION_FRAME)
	4101	{
	4102	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	4103	hi2c->State = HAL_I2C_STATE_READY;
	4104
	4105	/* Process Unlocked */
	4106	__HAL_UNLOCK(hi2c);
	4107
	4108	/* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */
	4109	HAL_I2C_ListenCpltCallback(hi2c);
	4110	}
	4111	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4112	else if (hi2c->State == HAL_I2C_STATE_BUSY_RX)
	4113	{
	4114	hi2c->State = HAL_I2C_STATE_READY;
	4115
	4116	/* Process Unlocked */
	4117	__HAL_UNLOCK(hi2c);
	4118
	4119	/* Call the Slave Rx Complete callback */
	4120	HAL_I2C_SlaveRxCpltCallback(hi2c);
	4121	}
	4122	else
	4123	{
	4124	hi2c->State = HAL_I2C_STATE_READY;
	4125
	4126	/* Process Unlocked */
	4127	__HAL_UNLOCK(hi2c);
	4128
	4129	/* Call the Slave Tx Complete callback */
	4130	HAL_I2C_SlaveTxCpltCallback(hi2c);
	4131	}
	4132	}
	4133
	4134	/**
	4135	* @brief I2C Listen complete process.
	4136	* @param hi2c I2C handle.
	4137	* @param ITFlags Interrupt flags to handle.
	4138	* @retval None
	4139	*/
	4140	static void I2C_ITListenCplt(I2C_HandleTypeDef *hi2c, uint32_t ITFlags)
	4141	{
	4142	/* Reset handle parameters */
	4143	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	4144	hi2c->PreviousState = I2C_STATE_NONE;
	4145	hi2c->State = HAL_I2C_STATE_READY;
	4146	hi2c->Mode = HAL_I2C_MODE_NONE;
	4147	hi2c->XferISR = NULL;
	4148
	4149	/* Store Last receive data if any */
	4150	if (((ITFlags & I2C_FLAG_RXNE) != RESET))
	4151	{
	4152	/* Read data from RXDR */
	4153	(*hi2c->pBuffPtr++) = hi2c->Instance->RXDR;
	4154
	4155	if ((hi2c->XferSize > 0U))
	4156	{
	4157	hi2c->XferSize--;
	4158	hi2c->XferCount--;
	4159
	4160	/* Set ErrorCode corresponding to a Non-Acknowledge */
	4161	hi2c->ErrorCode \|= HAL_I2C_ERROR_AF;
	4162	}
	4163	}
	4164
	4165	/* Disable all Interrupts*/
	4166	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT \| I2C_XFER_RX_IT \| I2C_XFER_TX_IT);
	4167
	4168	/* Clear NACK Flag */
	4169	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	4170
	4171	/* Process Unlocked */
	4172	__HAL_UNLOCK(hi2c);
	4173
	4174	/* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */
	4175	HAL_I2C_ListenCpltCallback(hi2c);
	4176	}
	4177
	4178	/**
	4179	* @brief I2C interrupts error process.
	4180	* @param hi2c I2C handle.
	4181	* @param ErrorCode Error code to handle.
	4182	* @retval None
	4183	*/
	4184	static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode)
	4185	{
	4186	/* Reset handle parameters */
	4187	hi2c->Mode = HAL_I2C_MODE_NONE;
	4188	hi2c->XferOptions = I2C_NO_OPTION_FRAME;
	4189	hi2c->XferCount = 0U;
	4190
	4191	/* Set new error code */
	4192	hi2c->ErrorCode \|= ErrorCode;
	4193
	4194	/* Disable Interrupts */
	4195	if ((hi2c->State == HAL_I2C_STATE_LISTEN) \|\|
	4196	(hi2c->State == HAL_I2C_STATE_BUSY_TX_LISTEN) \|\|
	4197	(hi2c->State == HAL_I2C_STATE_BUSY_RX_LISTEN))
	4198	{
	4199	/* Disable all interrupts, except interrupts related to LISTEN state */
	4200	I2C_Disable_IRQ(hi2c, I2C_XFER_RX_IT \| I2C_XFER_TX_IT);
	4201
	4202	/* keep HAL_I2C_STATE_LISTEN if set */
	4203	hi2c->State = HAL_I2C_STATE_LISTEN;
	4204	hi2c->PreviousState = I2C_STATE_NONE;
	4205	hi2c->XferISR = I2C_Slave_ISR_IT;
	4206	}
	4207	else
	4208	{
	4209	/* Disable all interrupts */
	4210	I2C_Disable_IRQ(hi2c, I2C_XFER_LISTEN_IT \| I2C_XFER_RX_IT \| I2C_XFER_TX_IT);
	4211
	4212	/* If state is an abort treatment on goind, don't change state */
	4213	/* This change will be do later */
	4214	if (hi2c->State != HAL_I2C_STATE_ABORT)
	4215	{
	4216	/* Set HAL_I2C_STATE_READY */
	4217	hi2c->State = HAL_I2C_STATE_READY;
	4218	}
	4219	hi2c->PreviousState = I2C_STATE_NONE;
	4220	hi2c->XferISR = NULL;
	4221	}
	4222
	4223	/* Abort DMA TX transfer if any */
	4224	if ((hi2c->Instance->CR1 & I2C_CR1_TXDMAEN) == I2C_CR1_TXDMAEN)
	4225	{
	4226	hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN;
	4227
	4228	/* Set the I2C DMA Abort callback :
	4229	will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */
	4230	hi2c->hdmatx->XferAbortCallback = I2C_DMAAbort;
	4231
	4232	/* Process Unlocked */
	4233	__HAL_UNLOCK(hi2c);
	4234
	4235	/* Abort DMA TX */
	4236	if (HAL_DMA_Abort_IT(hi2c->hdmatx) != HAL_OK)
	4237	{
	4238	/* Call Directly XferAbortCallback function in case of error */
	4239	hi2c->hdmatx->XferAbortCallback(hi2c->hdmatx);
	4240	}
	4241	}
	4242	/* Abort DMA RX transfer if any */
	4243	else if ((hi2c->Instance->CR1 & I2C_CR1_RXDMAEN) == I2C_CR1_RXDMAEN)
	4244	{
	4245	hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN;
	4246
	4247	/* Set the I2C DMA Abort callback :
	4248	will lead to call HAL_I2C_ErrorCallback() at end of DMA abort procedure */
	4249	hi2c->hdmarx->XferAbortCallback = I2C_DMAAbort;
	4250
	4251	/* Process Unlocked */
	4252	__HAL_UNLOCK(hi2c);
	4253
	4254	/* Abort DMA RX */
	4255	if (HAL_DMA_Abort_IT(hi2c->hdmarx) != HAL_OK)
	4256	{
	4257	/* Call Directly hi2c->hdmarx->XferAbortCallback function in case of error */
	4258	hi2c->hdmarx->XferAbortCallback(hi2c->hdmarx);
	4259	}
	4260	}
	4261	else if (hi2c->State == HAL_I2C_STATE_ABORT)
	4262	{
	4263	hi2c->State = HAL_I2C_STATE_READY;
	4264
	4265	/* Process Unlocked */
	4266	__HAL_UNLOCK(hi2c);
	4267
	4268	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4269	HAL_I2C_AbortCpltCallback(hi2c);
	4270	}
	4271	else
	4272	{
	4273	/* Process Unlocked */
	4274	__HAL_UNLOCK(hi2c);
	4275
	4276	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4277	HAL_I2C_ErrorCallback(hi2c);
	4278	}
	4279	}
	4280
	4281	/**
	4282	* @brief I2C Tx data register flush process.
	4283	* @param hi2c I2C handle.
	4284	* @retval None
	4285	*/
	4286	static void I2C_Flush_TXDR(I2C_HandleTypeDef *hi2c)
	4287	{
	4288	/* If a pending TXIS flag is set */
	4289	/* Write a dummy data in TXDR to clear it */
	4290	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) != RESET)
	4291	{
	4292	hi2c->Instance->TXDR = 0x00U;
	4293	}
	4294
	4295	/* Flush TX register if not empty */
	4296	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXE) == RESET)
	4297	{
	4298	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_TXE);
	4299	}
	4300	}
	4301
	4302	/**
	4303	* @brief DMA I2C master transmit process complete callback.
	4304	* @param hdma DMA handle
	4305	* @retval None
	4306	*/
	4307	static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma)
	4308	{
	4309	I2C_HandleTypeDef hi2c = (I2C_HandleTypeDef )((DMA_HandleTypeDef *)hdma)->Parent;
	4310
	4311	/* Disable DMA Request */
	4312	hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN;
	4313
	4314	/* If last transfer, enable STOP interrupt */
	4315	if (hi2c->XferCount == 0U)
	4316	{
	4317	/* Enable STOP interrupt */
	4318	I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT);
	4319	}
	4320	/* else prepare a new DMA transfer and enable TCReload interrupt */
	4321	else
	4322	{
	4323	/* Update Buffer pointer */
	4324	hi2c->pBuffPtr += hi2c->XferSize;
	4325
	4326	/* Set the XferSize to transfer */
	4327	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	4328	{
	4329	hi2c->XferSize = MAX_NBYTE_SIZE;
	4330	}
	4331	else
	4332	{
	4333	hi2c->XferSize = hi2c->XferCount;
	4334	}
	4335
	4336	/* Enable the DMA channel */
	4337	HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
	4338
	4339	/* Enable TC interrupts */
	4340	I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT);
	4341	}
	4342	}
	4343
	4344	/**
	4345	* @brief DMA I2C slave transmit process complete callback.
	4346	* @param hdma DMA handle
	4347	* @retval None
	4348	*/
	4349	static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma)
	4350	{
	4351	/* Prevent unused argument(s) compilation warning */
	4352	UNUSED(hdma);
	4353
	4354	/* No specific action, Master fully manage the generation of STOP condition */
	4355	/* Mean that this generation can arrive at any time, at the end or during DMA process */
	4356	/* So STOP condition should be manage through Interrupt treatment */
	4357	}
	4358
	4359	/**
	4360	* @brief DMA I2C master receive process complete callback.
	4361	* @param hdma DMA handle
	4362	* @retval None
	4363	*/
	4364	static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma)
	4365	{
	4366	I2C_HandleTypeDef hi2c = (I2C_HandleTypeDef )((DMA_HandleTypeDef *)hdma)->Parent;
	4367
	4368	/* Disable DMA Request */
	4369	hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN;
	4370
	4371	/* If last transfer, enable STOP interrupt */
	4372	if (hi2c->XferCount == 0U)
	4373	{
	4374	/* Enable STOP interrupt */
	4375	I2C_Enable_IRQ(hi2c, I2C_XFER_CPLT_IT);
	4376	}
	4377	/* else prepare a new DMA transfer and enable TCReload interrupt */
	4378	else
	4379	{
	4380	/* Update Buffer pointer */
	4381	hi2c->pBuffPtr += hi2c->XferSize;
	4382
	4383	/* Set the XferSize to transfer */
	4384	if (hi2c->XferCount > MAX_NBYTE_SIZE)
	4385	{
	4386	hi2c->XferSize = MAX_NBYTE_SIZE;
	4387	}
	4388	else
	4389	{
	4390	hi2c->XferSize = hi2c->XferCount;
	4391	}
	4392
	4393	/* Enable the DMA channel */
	4394	HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)hi2c->pBuffPtr, hi2c->XferSize);
	4395
	4396	/* Enable TC interrupts */
	4397	I2C_Enable_IRQ(hi2c, I2C_XFER_RELOAD_IT);
	4398	}
	4399	}
	4400
	4401	/**
	4402	* @brief DMA I2C slave receive process complete callback.
	4403	* @param hdma DMA handle
	4404	* @retval None
	4405	*/
	4406	static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma)
	4407	{
	4408	/* Prevent unused argument(s) compilation warning */
	4409	UNUSED(hdma);
	4410
	4411	/* No specific action, Master fully manage the generation of STOP condition */
	4412	/* Mean that this generation can arrive at any time, at the end or during DMA process */
	4413	/* So STOP condition should be manage through Interrupt treatment */
	4414	}
	4415
	4416	/**
	4417	* @brief DMA I2C communication error callback.
	4418	* @param hdma DMA handle
	4419	* @retval None
	4420	*/
	4421	static void I2C_DMAError(DMA_HandleTypeDef *hdma)
	4422	{
	4423	I2C_HandleTypeDef hi2c = (I2C_HandleTypeDef )((DMA_HandleTypeDef *)hdma)->Parent;
	4424
	4425	/* Disable Acknowledge */
	4426	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	4427
	4428	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4429	I2C_ITError(hi2c, HAL_I2C_ERROR_DMA);
	4430	}
	4431
	4432	/**
	4433	* @brief DMA I2C communication abort callback
	4434	* (To be called at end of DMA Abort procedure).
	4435	* @param hdma DMA handle.
	4436	* @retval None
	4437	*/
	4438	static void I2C_DMAAbort(DMA_HandleTypeDef *hdma)
	4439	{
	4440	I2C_HandleTypeDef hi2c = (I2C_HandleTypeDef )((DMA_HandleTypeDef *)hdma)->Parent;
	4441
	4442	/* Disable Acknowledge */
	4443	hi2c->Instance->CR2 \|= I2C_CR2_NACK;
	4444
	4445	/* Reset AbortCpltCallback */
	4446	hi2c->hdmatx->XferAbortCallback = NULL;
	4447	hi2c->hdmarx->XferAbortCallback = NULL;
	4448
	4449	/* Check if come from abort from user */
	4450	if (hi2c->State == HAL_I2C_STATE_ABORT)
	4451	{
	4452	hi2c->State = HAL_I2C_STATE_READY;
	4453
	4454	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4455	HAL_I2C_AbortCpltCallback(hi2c);
	4456	}
	4457	else
	4458	{
	4459	/* Call the corresponding callback to inform upper layer of End of Transfer */
	4460	HAL_I2C_ErrorCallback(hi2c);
	4461	}
	4462	}
	4463
	4464	/**
	4465	* @brief This function handles I2C Communication Timeout.
	4466	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4467	* the configuration information for the specified I2C.
	4468	* @param Flag Specifies the I2C flag to check.
	4469	* @param Status The new Flag status (SET or RESET).
	4470	* @param Timeout Timeout duration
	4471	* @param Tickstart Tick start value
	4472	* @retval HAL status
	4473	*/
	4474	static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status, uint32_t Timeout, uint32_t Tickstart)
	4475	{
	4476	while (__HAL_I2C_GET_FLAG(hi2c, Flag) == Status)
	4477	{
	4478	/* Check for the Timeout */
	4479	if (Timeout != HAL_MAX_DELAY)
	4480	{
	4481	if ((Timeout == 0U) \|\| ((HAL_GetTick() - Tickstart) > Timeout))
	4482	{
	4483	hi2c->State = HAL_I2C_STATE_READY;
	4484	hi2c->Mode = HAL_I2C_MODE_NONE;
	4485
	4486	/* Process Unlocked */
	4487	__HAL_UNLOCK(hi2c);
	4488	return HAL_TIMEOUT;
	4489	}
	4490	}
	4491	}
	4492	return HAL_OK;
	4493	}
	4494
	4495	/**
	4496	* @brief This function handles I2C Communication Timeout for specific usage of TXIS flag.
	4497	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4498	* the configuration information for the specified I2C.
	4499	* @param Timeout Timeout duration
	4500	* @param Tickstart Tick start value
	4501	* @retval HAL status
	4502	*/
	4503	static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
	4504	{
	4505	while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) == RESET)
	4506	{
	4507	/* Check if a NACK is detected */
	4508	if (I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK)
	4509	{
	4510	return HAL_ERROR;
	4511	}
	4512
	4513	/* Check for the Timeout */
	4514	if (Timeout != HAL_MAX_DELAY)
	4515	{
	4516	if ((Timeout == 0U) \|\| ((HAL_GetTick() - Tickstart) > Timeout))
	4517	{
	4518	hi2c->ErrorCode \|= HAL_I2C_ERROR_TIMEOUT;
	4519	hi2c->State = HAL_I2C_STATE_READY;
	4520	hi2c->Mode = HAL_I2C_MODE_NONE;
	4521
	4522	/* Process Unlocked */
	4523	__HAL_UNLOCK(hi2c);
	4524
	4525	return HAL_TIMEOUT;
	4526	}
	4527	}
	4528	}
	4529	return HAL_OK;
	4530	}
	4531
	4532	/**
	4533	* @brief This function handles I2C Communication Timeout for specific usage of STOP flag.
	4534	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4535	* the configuration information for the specified I2C.
	4536	* @param Timeout Timeout duration
	4537	* @param Tickstart Tick start value
	4538	* @retval HAL status
	4539	*/
	4540	static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
	4541	{
	4542	while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET)
	4543	{
	4544	/* Check if a NACK is detected */
	4545	if (I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK)
	4546	{
	4547	return HAL_ERROR;
	4548	}
	4549
	4550	/* Check for the Timeout */
	4551	if ((Timeout == 0U) \|\| ((HAL_GetTick() - Tickstart) > Timeout))
	4552	{
	4553	hi2c->ErrorCode \|= HAL_I2C_ERROR_TIMEOUT;
	4554	hi2c->State = HAL_I2C_STATE_READY;
	4555	hi2c->Mode = HAL_I2C_MODE_NONE;
	4556
	4557	/* Process Unlocked */
	4558	__HAL_UNLOCK(hi2c);
	4559
	4560	return HAL_TIMEOUT;
	4561	}
	4562	}
	4563	return HAL_OK;
	4564	}
	4565
	4566	/**
	4567	* @brief This function handles I2C Communication Timeout for specific usage of RXNE flag.
	4568	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4569	* the configuration information for the specified I2C.
	4570	* @param Timeout Timeout duration
	4571	* @param Tickstart Tick start value
	4572	* @retval HAL status
	4573	*/
	4574	static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
	4575	{
	4576	while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == RESET)
	4577	{
	4578	/* Check if a NACK is detected */
	4579	if (I2C_IsAcknowledgeFailed(hi2c, Timeout, Tickstart) != HAL_OK)
	4580	{
	4581	return HAL_ERROR;
	4582	}
	4583
	4584	/* Check if a STOPF is detected */
	4585	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == SET)
	4586	{
	4587	/* Clear STOP Flag */
	4588	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	4589
	4590	/* Clear Configuration Register 2 */
	4591	I2C_RESET_CR2(hi2c);
	4592
	4593	hi2c->ErrorCode = HAL_I2C_ERROR_NONE;
	4594	hi2c->State = HAL_I2C_STATE_READY;
	4595	hi2c->Mode = HAL_I2C_MODE_NONE;
	4596
	4597	/* Process Unlocked */
	4598	__HAL_UNLOCK(hi2c);
	4599
	4600	return HAL_ERROR;
	4601	}
	4602
	4603	/* Check for the Timeout */
	4604	if ((Timeout == 0U) \|\| ((HAL_GetTick() - Tickstart) > Timeout))
	4605	{
	4606	hi2c->ErrorCode \|= HAL_I2C_ERROR_TIMEOUT;
	4607	hi2c->State = HAL_I2C_STATE_READY;
	4608
	4609	/* Process Unlocked */
	4610	__HAL_UNLOCK(hi2c);
	4611
	4612	return HAL_TIMEOUT;
	4613	}
	4614	}
	4615	return HAL_OK;
	4616	}
	4617
	4618	/**
	4619	* @brief This function handles Acknowledge failed detection during an I2C Communication.
	4620	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4621	* the configuration information for the specified I2C.
	4622	* @param Timeout Timeout duration
	4623	* @param Tickstart Tick start value
	4624	* @retval HAL status
	4625	*/
	4626	static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
	4627	{
	4628	if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == SET)
	4629	{
	4630	/* Wait until STOP Flag is reset */
	4631	/* AutoEnd should be initiate after AF */
	4632	while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET)
	4633	{
	4634	/* Check for the Timeout */
	4635	if (Timeout != HAL_MAX_DELAY)
	4636	{
	4637	if ((Timeout == 0U) \|\| ((HAL_GetTick() - Tickstart) > Timeout))
	4638	{
	4639	hi2c->State = HAL_I2C_STATE_READY;
	4640	hi2c->Mode = HAL_I2C_MODE_NONE;
	4641
	4642	/* Process Unlocked */
	4643	__HAL_UNLOCK(hi2c);
	4644	return HAL_TIMEOUT;
	4645	}
	4646	}
	4647	}
	4648
	4649	/* Clear NACKF Flag */
	4650	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
	4651
	4652	/* Clear STOP Flag */
	4653	__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_STOPF);
	4654
	4655	/* Flush TX register */
	4656	I2C_Flush_TXDR(hi2c);
	4657
	4658	/* Clear Configuration Register 2 */
	4659	I2C_RESET_CR2(hi2c);
	4660
	4661	hi2c->ErrorCode = HAL_I2C_ERROR_AF;
	4662	hi2c->State = HAL_I2C_STATE_READY;
	4663	hi2c->Mode = HAL_I2C_MODE_NONE;
	4664
	4665	/* Process Unlocked */
	4666	__HAL_UNLOCK(hi2c);
	4667
	4668	return HAL_ERROR;
	4669	}
	4670	return HAL_OK;
	4671	}
	4672
	4673	/**
	4674	* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set).
	4675	* @param hi2c I2C handle.
	4676	* @param DevAddress Specifies the slave address to be programmed.
	4677	* @param Size Specifies the number of bytes to be programmed.
	4678	* This parameter must be a value between 0 and 255.
	4679	* @param Mode New state of the I2C START condition generation.
	4680	* This parameter can be one of the following values:
	4681	* @arg @ref I2C_RELOAD_MODE Enable Reload mode .
	4682	* @arg @ref I2C_AUTOEND_MODE Enable Automatic end mode.
	4683	* @arg @ref I2C_SOFTEND_MODE Enable Software end mode.
	4684	* @param Request New state of the I2C START condition generation.
	4685	* This parameter can be one of the following values:
	4686	* @arg @ref I2C_NO_STARTSTOP Don't Generate stop and start condition.
	4687	* @arg @ref I2C_GENERATE_STOP Generate stop condition (Size should be set to 0).
	4688	* @arg @ref I2C_GENERATE_START_READ Generate Restart for read request.
	4689	* @arg @ref I2C_GENERATE_START_WRITE Generate Restart for write request.
	4690	* @retval None
	4691	*/
	4692	static void I2C_TransferConfig(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request)
	4693	{
	4694	uint32_t tmpreg = 0U;
	4695
	4696	/* Check the parameters */
	4697	assert_param(IS_I2C_ALL_INSTANCE(hi2c->Instance));
	4698	assert_param(IS_TRANSFER_MODE(Mode));
	4699	assert_param(IS_TRANSFER_REQUEST(Request));
	4700
	4701	/* Get the CR2 register value */
	4702	tmpreg = hi2c->Instance->CR2;
	4703
	4704	/* clear tmpreg specific bits */
	4705	tmpreg &= (uint32_t)~((uint32_t)(I2C_CR2_SADD \| I2C_CR2_NBYTES \| I2C_CR2_RELOAD \| I2C_CR2_AUTOEND \| I2C_CR2_RD_WRN \| I2C_CR2_START \| I2C_CR2_STOP));
	4706
	4707	/* update tmpreg */
	4708	tmpreg \|= (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) \| (((uint32_t)Size << 16) & I2C_CR2_NBYTES) \| \
	4709	(uint32_t)Mode \| (uint32_t)Request);
	4710
	4711	/* update CR2 register */
	4712	hi2c->Instance->CR2 = tmpreg;
	4713	}
	4714
	4715	/**
	4716	* @brief Manage the enabling of Interrupts.
	4717	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4718	* the configuration information for the specified I2C.
	4719	* @param InterruptRequest Value of @ref I2C_Interrupt_configuration_definition.
	4720	* @retval HAL status
	4721	*/
	4722	static HAL_StatusTypeDef I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest)
	4723	{
	4724	uint32_t tmpisr = 0U;
	4725
	4726	if ((hi2c->XferISR == I2C_Master_ISR_DMA) \|\| \
	4727	(hi2c->XferISR == I2C_Slave_ISR_DMA))
	4728	{
	4729	if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT)
	4730	{
	4731	/* Enable ERR, STOP, NACK and ADDR interrupts */
	4732	tmpisr \|= I2C_IT_ADDRI \| I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_ERRI;
	4733	}
	4734
	4735	if ((InterruptRequest & I2C_XFER_ERROR_IT) == I2C_XFER_ERROR_IT)
	4736	{
	4737	/* Enable ERR and NACK interrupts */
	4738	tmpisr \|= I2C_IT_ERRI \| I2C_IT_NACKI;
	4739	}
	4740
	4741	if ((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT)
	4742	{
	4743	/* Enable STOP interrupts */
	4744	tmpisr \|= I2C_IT_STOPI;
	4745	}
	4746
	4747	if ((InterruptRequest & I2C_XFER_RELOAD_IT) == I2C_XFER_RELOAD_IT)
	4748	{
	4749	/* Enable TC interrupts */
	4750	tmpisr \|= I2C_IT_TCI;
	4751	}
	4752	}
	4753	else
	4754	{
	4755	if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT)
	4756	{
	4757	/* Enable ERR, STOP, NACK, and ADDR interrupts */
	4758	tmpisr \|= I2C_IT_ADDRI \| I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_ERRI;
	4759	}
	4760
	4761	if ((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT)
	4762	{
	4763	/* Enable ERR, TC, STOP, NACK and RXI interrupts */
	4764	tmpisr \|= I2C_IT_ERRI \| I2C_IT_TCI \| I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_TXI;
	4765	}
	4766
	4767	if ((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT)
	4768	{
	4769	/* Enable ERR, TC, STOP, NACK and TXI interrupts */
	4770	tmpisr \|= I2C_IT_ERRI \| I2C_IT_TCI \| I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_RXI;
	4771	}
	4772
	4773	if ((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT)
	4774	{
	4775	/* Enable STOP interrupts */
	4776	tmpisr \|= I2C_IT_STOPI;
	4777	}
	4778	}
	4779
	4780	/* Enable interrupts only at the end */
	4781	/* to avoid the risk of I2C interrupt handle execution before */
	4782	/* all interrupts requested done */
	4783	__HAL_I2C_ENABLE_IT(hi2c, tmpisr);
	4784
	4785	return HAL_OK;
	4786	}
	4787
	4788	/**
	4789	* @brief Manage the disabling of Interrupts.
	4790	* @param hi2c Pointer to a I2C_HandleTypeDef structure that contains
	4791	* the configuration information for the specified I2C.
	4792	* @param InterruptRequest Value of @ref I2C_Interrupt_configuration_definition.
	4793	* @retval HAL status
	4794	*/
	4795	static HAL_StatusTypeDef I2C_Disable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest)
	4796	{
	4797	uint32_t tmpisr = 0U;
	4798
	4799	if ((InterruptRequest & I2C_XFER_TX_IT) == I2C_XFER_TX_IT)
	4800	{
	4801	/* Disable TC and TXI interrupts */
	4802	tmpisr \|= I2C_IT_TCI \| I2C_IT_TXI;
	4803
	4804	if ((hi2c->State & HAL_I2C_STATE_LISTEN) != HAL_I2C_STATE_LISTEN)
	4805	{
	4806	/* Disable NACK and STOP interrupts */
	4807	tmpisr \|= I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_ERRI;
	4808	}
	4809	}
	4810
	4811	if ((InterruptRequest & I2C_XFER_RX_IT) == I2C_XFER_RX_IT)
	4812	{
	4813	/* Disable TC and RXI interrupts */
	4814	tmpisr \|= I2C_IT_TCI \| I2C_IT_RXI;
	4815
	4816	if ((hi2c->State & HAL_I2C_STATE_LISTEN) != HAL_I2C_STATE_LISTEN)
	4817	{
	4818	/* Disable NACK and STOP interrupts */
	4819	tmpisr \|= I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_ERRI;
	4820	}
	4821	}
	4822
	4823	if ((InterruptRequest & I2C_XFER_LISTEN_IT) == I2C_XFER_LISTEN_IT)
	4824	{
	4825	/* Disable ADDR, NACK and STOP interrupts */
	4826	tmpisr \|= I2C_IT_ADDRI \| I2C_IT_STOPI \| I2C_IT_NACKI \| I2C_IT_ERRI;
	4827	}
	4828
	4829	if ((InterruptRequest & I2C_XFER_ERROR_IT) == I2C_XFER_ERROR_IT)
	4830	{
	4831	/* Enable ERR and NACK interrupts */
	4832	tmpisr \|= I2C_IT_ERRI \| I2C_IT_NACKI;
	4833	}
	4834
	4835	if ((InterruptRequest & I2C_XFER_CPLT_IT) == I2C_XFER_CPLT_IT)
	4836	{
	4837	/* Enable STOP interrupts */
	4838	tmpisr \|= I2C_IT_STOPI;
	4839	}
	4840
	4841	if ((InterruptRequest & I2C_XFER_RELOAD_IT) == I2C_XFER_RELOAD_IT)
	4842	{
	4843	/* Enable TC interrupts */
	4844	tmpisr \|= I2C_IT_TCI;
	4845	}
	4846
	4847	/* Disable interrupts only at the end */
	4848	/* to avoid a breaking situation like at "t" time */
	4849	/* all disable interrupts request are not done */
	4850	__HAL_I2C_DISABLE_IT(hi2c, tmpisr);
	4851
	4852	return HAL_OK;
	4853	}
	4854
	4855	/**
	4856	* @}
	4857	*/
	4858
	4859	#endif /* HAL_I2C_MODULE_ENABLED */
	4860	/**
	4861	* @}
	4862	*/
	4863
	4864	/**
	4865	* @}
	4866	*/
	4867
	4868	/********************** (C) COPYRIGHT STMicroelectronics *END OF FILE**/